28358
19
Zoom out
Zoom in
Vorherige Seite
1/55
Nächste Seite
12
CAUTION
INSTALLATION
3.6 ELECTRICAL CONNECTION
3.6.1 DC POWER CABLE
The RADAR 3000 will work with any ship’s mains within the 10.2 to 42 V
range, since it contains a power regulator circuit. Connect the power cable to a
DC source. The power cable normally should be wired through the circuit breaker.
The white lead wire of the power cable should be connected to the positive
source terminal and the black lead to negative source terminal. The shielded
wire should be connected to the ship’s RF ground. Should the power connec-
tions be inadvertently reversed, a protective fuse will blow. Recheck the input
power leads for correct polarity with a VOM and reconnect the leads observing
correct polarity. Replace the fuse.
3.6.2 EXTERNAL SYSTEM INTERFACE
FIG. 3-4 SCANNER UNIT CABLE CONNECTION PROCEDURE
Ground Terminal
Clamping Plate
Rubber Grommet
Interconnecting Cable
Cable Clamp
TO CME-229
J1
P1
W1
PW1
To connect with NAV-AID and/or compass, make sure pin as-
signment, if used same connector.
In case of different pin assignment, the RADAR 3000 or con-
nected NAV-AID will be damaged.
12
CAUTION
INSTALLATION
3.6 ELECTRICAL CONNECTION
3.6.1 DC POWER CABLE
The RADAR 3000 will work with any ship’s mains within the 10.2 to 42 V
range, since it contains a power regulator circuit. Connect the power cable to a
DC source. The power cable normally should be wired through the circuit breaker.
The white lead wire of the power cable should be connected to the positive
source terminal and the black lead to negative source terminal. The shielded
wire should be connected to the ship’s RF ground. Should the power connec-
tions be inadvertently reversed, a protective fuse will blow. Recheck the input
power leads for correct polarity with a VOM and reconnect the leads observing
correct polarity. Replace the fuse.
3.6.2 EXTERNAL SYSTEM INTERFACE
FIG. 3-4 SCANNER UNIT CABLE CONNECTION PROCEDURE
Ground Terminal
Clamping Plate
Rubber Grommet
Interconnecting Cable
Cable Clamp
TO CME-229
J1
P1
W1
PW1
To connect with NAV-AID and/or compass, make sure pin as-
signment, if used same connector.
In case of different pin assignment, the RADAR 3000 or con-
nected NAV-AID will be damaged.
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für JRC Radar3000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info