614741
68
Zoom out
Zoom in
Vorherige Seite
1/72
Nächste Seite
Performance checklist
If sewing difficulties occur, make sure the instructions are correctly followed.
If a problem still exists, the reminders below may help solve it.
Specification table
Needle breaks.
Machine fails to
feed fabric.
* Machine runs idle.
* Stitch length is set at left position of manual
mode.
* Drop feed is engaged.
* Return bobbin winder to the left.
* Set stitch length at auto mode or right
position of manual mode.
* Disengage drop feed.
* Needle is bent. Needle is not correctly
installed.
* Presser foot does not match pattern
selected.
* Relation among needle, thread and fabric
is not appropriate.
* Change needle with a new one and install it
correctly.
* Use presser foot that matches the pattern
selected.
* Use needle and thread that match fabric.
Page
Thread breaks.
Bobbin thread
breaks.
Skipped stitches.
15-17
27,28
14
* Machine head is incorrectly threaded.
* Thread is caught in a part that is not to be
threaded.
* Needle thread tension is too high.
* Needle is bent.
* Re-thread machine head correctly.
* Check spool pin and thread guide for thread
tangling.
* Adjust thread tension adequately.
* Replace needle with a new one.
* Needle is not installed correctly.
* Needle is bent.
* Machine head is not correctly threaded.
* Correctly attach needle.
* Replace needle with a new one.
* Re-thread machine head correctly.
22
23
25
Puckering occurs.
Thread tangles on
wrong side of fabric.
Loud noise, heavy
to turn the handwheel.
Sewing machine will
not sew when start
button is pressed.
Needle cannot be
threaded.
* Thread tension is too high.
* Needle and thread do not match fabric.
* Adjust thread tension adequately.
* Use needle and thread that correctly match
fabric.
* Machine head is not correctly threaded. * Re-thread machine head correctly.
* Lint or dust has accumulated in hook. * Clean up hook.
* Bobbin winder is set in bobbin winding
position.
* Controller is connected to machine.
* Return bobbin winder to the left.
* Start machine with controller or remove
connector from machine.
* Needle is not raised to its highest
position.
* Needle is not installed by fully inserting
into needle clamp.
* Sewing machine is rotated by mistake with
needle threading lever lowered (during
needle threading).
* Turn handwheel to raise needle to its highest
position.
* Correctly install needle.
* Turn handwheel slightly away from you (in
direction opposite to normal direction of
rotation in which handwheel turns to perform
sewing).
18-20
-
24
22
22
22
18-20
24
25
18-20
65
15-17
12
19
22
-
Problem Cause (Reason) Action to be taken
Item Specification
Dimensions 410 (W) x 300 (H) x 180 (D) mm
7.3kg (when attached with case: 8.4kg)
120V / 1.0A 60Hz (USA and Canada only)
220-230V / 100W 50 / 60Hz
120V / 15W (USA and Canada only)
240V / 15W
440 (W) x 305 (H) x 215 (D) mm
Weight
Dimensions when attached
with case
Rated voltage/ Power con-
sumption
Power consumption of lamp
66
68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Juki HZL-E71 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info