660668
53
Zoom out
Zoom in
Vorherige Seite
1/56
Nächste Seite
Estimated timing for laser light source replacement
Displays using the solid/blinking light of the “LIGHT” indicator. The “STANDBY/ON” indicator, which shows the operating
mode of the unit, is also displayed simultaneously.
* “LIGHT” indicator does not light up when “LED Indication” is set to “Off” (p. 37).
.
LIGHT WARNING
STANDBY/ON
GH
LIG
HT
If 40,000 hours have elapsed, the
brightness will be half the brightness at
shipment.
“LIGHT” lights up (orange)
Lights up when the “LD Current” gauge
reaches 95 and above. (When the Auto
Intensity function is On.)
Warning display
You can tell the details of a warning from the (repeated) displays of the “WARNING” and “LIGHT” indicators. The
“STANDBY/ON” indicator, which shows the operating mode of the unit, is also displayed simultaneously.
The projector enters into Warning mode once the “WARNING” indicator is displayed. The power cannot be turned on
again under this condition.
Allow the projector to cool down for a while, then check the following.
Indicator Status (Solid/Blinking)
Blinking
Frequency
Description Check and Countermeasure
.
LIGHT WARNING
STANDBY/ON
WARNING
(Red)(*)Mode
Display
x1
Abnormality in the power supply
0
Check that nothing is blocking
the air inlets.
0
Check that the external
temperature is normal.
Countermeasure: Leave the unit
unoperated until it cools down.
After that, turn on the power again.
x2
Cooling fan stopped abnormally
x3 Internal temperature is
abnormally high
x4 External temperature is too high
x5 Abnormal circuit operation
.
LIGHT WARNING
STANDBY/ON
WARNING
LIGHT
Blinking
Simultaneously
(Red)
(Orange)
Mode
Display
x1
Abnormal circuit operation
x2
x3
.
LIGHT WARNING
STANDBY/ON
LIGHT
RN
WAR
NING
(Red)
(Orange)
Mode
Display
x1
LD Driver or LD light source
Error
Countermeasure: Leave the unit
unoperated until it cools down.
After that, turn on the power again.
x2 Wheel Error
x3 Color Sensor Error
x4 Inter Lock
If the Warning mode is activated again, wait for the cooling fan to stop, followed by pulling out the power plug from the
outlet.
Request for repair at your authorized dealer or a nearby service center.
(*) If the scheduled time for laser light source replacement is exceeded, the indicator may light up.
53
Others
53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für JVC DLA-VS2300ZG wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info