Bedienungsanleitung JVC GD-V4210PCE (Seite 36 von 40) (Englisch)

40064

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

• Is the power cord disconnected?

•Is the MAIN POWER switch turned on?

•Is the correct input selected?

•Are the devices connected correctly?

•Are signals being supplied from the

connected devices?

•Is RGB INPUT set correctly if using the

RGB terminals?

•Are input signals (scanning frequency,

etc.) appropriate?

•Is brightness adjusted correctly?

•Is volume set at minimum?

•Are the diagnostic lamps turned on?

•Is the signal RGB input?

•Is brightness adjusted correctly?

•Is picture quality (colour density, etc.)

adjusted correctly?

•Is the correct broadcast system (colour

system) selected?

•Are signals (scanning frequency, etc.) to

connected devices appropriate?

•Is the size or position of the screen

adjusted properly?

•Are the batteries correctly set?

•Are the batteries exhausted?

•Is there any object blocking the path

between the remote control and remote

sensor?

•Is the Monitor too far away from you?

•Is the Monitor connected serially to

another Monitor (Serial Connection)?

•Is the Control Lock function in use?

Troubleshooting

Solutions to common problems related to the Monitor are described here. If none of the solutions presented here solves the

problem, unplug the Monitor and consult an authorized dealer or service center.

Symptom Probable cause Corrective action Page

•Insert the power cord (plug) firmly.

•Turn on the MAIN POWER switch.

•Select the correct input by pressing

VIDEO A, VIDEO B, COMPO. and

RGB on the remote control (or INPUT

on the Monitor).

•Connect the devices correctly.

•Set the devices correctly.

•Set it correctly.

•Check if the signal is appropriate

(scanning frequency, etc.), and input

the appropriate signal.

•Adjust brightness on the menu.

•Adjust volume.

•Refer to “Self-diagnostic indication,”

and take an appropriate action.

•Adjust CLOCK PHASE using the

menu.

•Adjust BRIGHT (brightness) using the

menu.

•Adjust PICTURE using the menu.

•Set SIGNAL MODE (colour system) to

“AUTO.”

•Check if the signal is appropriate

(scanning frequency, etc.), and input

the appropriate signal.

•Adjust H.SIZE, V.SIZE, H.POSITION

or V.POSITION using the menu.

•Insert batteries correctly, observing the

polarities (ª and ·).

•Replace with new batteries.

•Remove any blocking object.

•Move toward the Monitor, then operate

the remote control.

•Only Master Monitor can be controlled

by the remote control when connected

serially.

•Set the Control Lock function to “OFF”

using the menu.

12, 13

—

Power is not supplied.

Video image does not

appear, or audio

sound does not occur.

The picture becomes

blurred.

Colour is abnormally

dark or bright.

Colour is poor or

unstable.

The picture is cut or

shifted toward one

side.

The remote control

does not work.

The buttons on the

Monitor do not work.

31-40.GD-V4210PZW[EN]/f 00.9.29, 5:56 PM36

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC GD-V4210PCE Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info