532511
41
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
31
Troubleshooting
Symptom Check Points Action
Video
troubles
Colors in the monitor screen are
abnormal. (During genlocking)
Is the SC phase adjusted properly?
A P12
Synchronization is not possible. Are the Tri-level sync signal or BB signals applied to the
[GENLOCK INPUT] connectors?
Is the VTR playback signal supplied directly without passing
through a TBC?
A
P12
Control
troubles
Pressing the corresponding
button cannot start the operation.
A
<EXT>
B
is displayed on the LCD.
Functions that are not available on the camera cannot be
controlled.
hCheck the camera functions again.
^
The LCD display keeps on
displaying
A
NOW INITIALIZING
JUST A MOMENTB.
Are cables connected properly?
Is the power switch of the camera set to ON?
A P8
A P9
A P10
The LCD display keeps on
display
A
PLEASE CHECK THE
CAMERAB.
Are cables connected properly?
Is the power switch of the camera set to ON?
(When power of camera is turned off while RM-HP790DU/RM-
HP790DE is on, APLEASE CHECK THE CAMERAB will be
displayed after about 20 seconds if RM-HP790DU/RM-HP790DE
is operated. In addition, when turning on RM-HP790DU/RM-
HP790DE while the power switch of camera is off, similar display
will appear after about 30 seconds. )
A
P8
A P9
A P10
LCD display shows
A
---B. The connected camera does not have the assigned function.
Check the camera functions again and assign the proper functions
to the [F1] to [F4] buttons.
A P25
white balance adjustment cannot
be started.
Is the [W. BAL] switch set to AAB or ABB?
Is FAS or FAW ON (which is indicated by the lighting of the
[AUTO] light)?
A P18
The white balance adjustment will
not complete.
Are the color temperature filters and lighting conditions
appropriate?
Does the object have colors?
A P18
The tally lamp does not light. Is the tally system of the RM-HP790DU/RM-HP790DE compatible
with that of the camera system?
The RM-HP790DU/RM-HP790DE has been set to the voltage
supply at the factory.
If it is required to use the [TALLY] input in the contact supply mode,
the setting of the internal circuitry should be changed ; consult the
nearest JVC-authorized service agent.
A P14
Incorrect operation even when
FAS button is ON.
Is the Studio cable of KA-M790G pulled out or loose?
hConnect the cable properly.
^
A
E.02B will be displayed on RM-
LP25U
Are cables connected properly?
Is the power switch of the camera set to ON?
(When power of camera is turned off while RM-HP790DU/RM-
HP790DE/RM-LP25U is on, similar display will appear after about
10 seconds.)
A
P8
A P9
A P10
[OPERATE] button of RM-LP25U
keeps blinking.
Are cables connected properly?
Is the power switch of the camera set to ON?
(When turning on RM-HP790DU/RM-HP790DE/RM-LP25U while
the power switch of camera is off, the [OPERATE] button will keep
blinking.)
A P8
A P9
A P10
41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für JVC GY-HM790 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info