Bedienungsanleitung JVC HR-J287MS (Seite 12 von 16) (Englisch)

476524

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Page 12 September 3, 2001 9:09 am

Changing Remote Control Code

This remote control is capable of transmitting two control codes;

one set to respond to A code control signals and another set to

respond to B code control signals. This remote control is preset to

send A code signals because your recorder is initially set to

respond to A code signals. You can easily modify your recorder

and the remote control to respond to B code signals. When using

two JVC recorders, set two recorders and their remote controls to

different codes, so that you can operate these recorders separately.

Set remote control code for remote control

A Press and hold VCR.

B Press the Number key “2”.

C Press OK, and release VCR.

● The remote control now can transmit B code control signals.

Check remote control code for recorder

Press and hold PLAY (4) on the recorder for more than 5 seconds

while the recorder is turned off. The code currently set appears on

the display panel.

Change code for recorder

Press any key on the remote control. The recorder now responds

to B code control signals.

● To set the remote control and the recorder back to A code

control signals, repeat the same procedure as shown above

except pressing the Number key “1” in step B of 1.

To control two recorders with the same remote

control

You can control two JVC recorders by switching the remote

control code for the remote control between A and B (

੬

step A),

keeping two recorders to different control codes.

● To change only the remote control code for the remote control,

DO NOT perform steps B and C.

Editing

You can use your recorder as the playback or recording deck. You

can use a camcorder as the source player and your recorder as the

recording deck. Refer also to the other components’ instruction

manuals for connection and its operations.

Make connections

Example: When using this recorder as the source player

● When using this recorder as the recording deck, connect this

recorder’s AV input connectors to the AV output connectors on

the other recorder. If the source player is monaural, connect the

audio output connector on the source player to the left audio

input connector on this recorder.

Load cassettes

Insert the playback cassette into the source player and the cassette

to be recorded on into the recording deck.

Select input mode on recording deck

Select the correct external input on the recording deck.

On this recorder (when using this recorder as the recording deck);

Select “L-1” — when connecting the other recorder to the AV

input connectors on the rear panel.

On the remote control

Press AUX or PR+/–.

On the recorder

Press PAUSE[PR], and then FF[PR+] or REW[PR–]. See step B in

“Basic Recording”.

Select edit mode

Set the edit mode to “ON” for the recorders if such a mode is

equipped.

● On this recorder, set “PICTURE CONTROL” to “EDIT”.

Start playback

Press PLAY (

) on the source player.

Start recording

Press REC (

) on the recording deck.

To AV input

This recorder (for playback)

Another recorder (for recording)

AV cable

(not supplied)

To AUDIO/VIDEO OUT

– Other Functions –

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC HR-J287MS Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info