Bedienungsanleitung JVC HR-J448 (Seite 43 von 48) (Englisch)

528232

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

EN 43

Confirm that the camcorder is

properly connected.

Set the input mode to “AU”.

● The camcorder has not been

properly connected.

● The input mode is not correct.

4. Camcorder recording is not

possible.

TIMER RECORDING

CORRECTIVE ACTION

Re-perform the clock and/or timer

settings.

Press TIMER and confirm that “‰“ is

displayed on the display panel.

Timer programming can’t be

performed while a timer recording is

in progress. Wait until it finishes.

Load a cassette with the Record

Safety tab intact, or cover the hole

using adhesive tape.

Remove the cassette and cover the

hole with adhesive tape, or insert a

cassette with the Record Safety tab

intact.

Check the programmed data and re-

program as necessary, then press

TIMER again.

The programme may not have been

recorded in its entirety. Next time

make sure you have enough time on

the tape to record the entire

programme.

Refer to "Guide Program Number Set"

and re-perform the procedure

(

੬ pg. 10).

SYMPTOM

1. Timer recording won’t work.

2. On-screen timer programming is

not possible.

3. “‰“ and “]“ on the display

panel won’t stop blinking.

4. The cassette is automatically

ejected, and “‰“ and “]“ on the

display panel won’t stop blinking.

5. “‰“ blinks for 10 seconds and the

Timer mode is disengaged.

6. The cassette is automatically

ejected, the power shuts off and

“‰“ and “]“ won’t stop

blinking.

7. SHOWVIEW does not timer-record

properly.

POSSIBLE CAUSE

● The clock and/or the timer have

been set incorrectly.

● The timer is not engaged.

● Timer recording is in progress.

● The timer is engaged but there’s no

cassette loaded.

● The loaded cassette has had its

Record Safety tab removed.

● TIMER has been pressed when there

are no programs in memory, or the

timer record information has been

programmed incorrectly.

● The end of the tape was reached

during timer recording.

● The recorder’s channel positions

have been set incorrectly.

OTHER PROBLEMS

CORRECTIVE ACTION

Position the camcorder so its

microphone is away from the TV.

Turn the TV’s volume down.

If you need the skipped channels,

restore them (੬ pg. 36).

Press PAUSE to pause the recording,

change channels, then press PLAY to

resume recording.

Perform manual setting again.

Connect the TV aerial cable to the

recorder properly and turn off the

recorder power once, then turn the

recorder power back on again. The

recorder will try Auto Set Up again

(

੬ pg. 4).

SYMPTOM

1. Whistling or howling is heard from

the TV during camcorder record-

ing.

2. When scanning channels, some of

them are skipped over.

3. The channel cannot be changed.

4. Channel settings that were made

manually seem to have changed or

disappeared.

5. No channels are stored in the

recorder's memory.

POSSIBLE CAUSE

● The camcorder’s microphone is too

close to the TV.

● The TV’s volume is too high.

● Those channels have been desig-

nated to be skipped.

● Recording is in progress.

● After the manual settings were

made, Auto Channel Set was

performed.

● The TV aerial cable was not

connected to the recorder when

Auto Set Up was performed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC HR-J448 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info