Bedienungsanleitung JVC HR-J648 (Seite 42 von 48) (Englisch)

528231

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

42 EN

TROUBLESHOOTING

Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily

corrected, and this can save you the trouble of sending your video recorder off for repair.

POSSIBLE CAUSE

● The mains power cord is discon-

nected.

● “‰“ is displayed on the display

panel with Auto Timer set to "OFF".

SYMPTOM

1. No power is applied to the

recorder.

2. The clock is functioning properly,

but the recorder cannot be

powered.

CORRECTIVE ACTION

Connect the mains power cord.

Press the TIMER button to turn the

“‰“ indicator off.

SYMPTOM

1. The tape does not run during

recording.

2. The tape stops during rewind or

fast-forward.

3. The tape will not rewind or fast-

forward.

CORRECTIVE ACTION

Press PLAY to turn the “^“ indicator

off.

Press C.MEMORY to deactivate the

Counter Memory function and turn

the “M“ indicator off.

Check the cassette.

SYMPTOM

1. The playback picture does not

appear while the tape is running.

2. Noise appears during visual search.

3. Noise appears during normal

playback.

4. Noise appears during slow-motion

playback.

5. Noise appears during still play-

back.

6. (HR-J648E/EH only) Breaks are

noticeable in Hi-Fi soundtrack

7. The playback picture is blurred or

interrupted while TV broadcasts are

clear.

POSSIBLE CAUSE

● If you’re using the RF OUT connec-

tion . . .

. . . the TV receiver’s channel selector

is not set to the VIDEO channel.

. . . the recorder's VIDEO channel

has not been correctly set.

● If you’re using the AV connection, the

TV receiver is not set to the AV mode.

● This is normal.

● The automatic tracking mode is

engaged.

● The automatic tracking mode is

engaged.

● Automatic tracking is engaged.

● The video heads may be dirty.

CORRECTIVE ACTION

If you are using the RF OUT connec-

tion . . .

. . . set the TV receiver to the VIDEO

channel. (੬ pg. 8)

. . . Perform "Video Channel Set"

(੬ pg. 8)

If you are using the AV connection,

set the TV to its AV mode.

Try manual tracking. (੬ pg. 14)

Press TV PROG.+ or – a few times to

remove the noise bars from the screen.

Engage and adjust tracking manually.

(੬ pg. 14)

Consult your JVC dealer.

POSSIBLE CAUSE

● “^“ is displayed on the display

panel.

● “M“ is displayed on the display

panel.

● The tape is already fully rewound or

fast-forwarded.

CORRECTIVE ACTION

Insert a cassette, or using adhesive

tape, reseal the slot where the tab

was removed.

Set to the desired channel.

Confirm that the source is properly

connected.

Confirm that all units’ power switches

are turned on.

Set the input mode to “AU”.

POSSIBLE CAUSE

● There is no cassette loaded, or the

cassette loaded has had its Record

Safety tab removed.

● “AU” has been selected as the input

mode.

● The source (another video recorder,

camcorder) has not been properly

connected.

● All necessary power switches have

not been turned on.

● The input mode is not correct.

SYMPTOM

1. Recording cannot be started.

2. TV broadcasts cannot be recorded.

RECORDING

PLAYBACK

TAPE TRANSPORT

POWER

3. Tape-to-tape editing is not

possible.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC HR-J648 Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info