Bedienungsanleitung JVC RX-E100RSL (Seite 48 von 50) (Englisch)

469766

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

Troubleshooting

Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center.

PROBLEM

The power does not comes on.

No sound from speakers.

Sound from one speaker only.

Continuous hiss or buzzing during FM

reception.

Occasional cracking noise during FM

reception.

“OVERLOAD” starts flashing on the

display.

The STANDBY lamp lights up after

turning on the power, but soon the unit

turns off (into standby mode).

Remote control does not operate as you

intend.

Remote control does not work.

SOLUTION

Plug the power cord into an AC outlet.

Check speaker wiring and reconnect if

necessary.

Select the correct source.

Press MUTING to cancel the mute.

Select the correct input mode (analogue or

digital).

Check connections.

Adjust the balance properly (see page 20).

Connect an outdoor FM antenna or contact

your dealer.

Select a new station.

Check with your dealer to be sure you have

a correct antenna.

Check connections.

Move the antenna farther from automobile

traffic.

1. Press POWER on the front panel to turn

off the unit.

2. Stop the playback source.

3. Turn on the unit again, and adjust the

volume.

Press POWER on the front panel to turn off

the unit, then check the speaker wiring.

If “OVERLOAD” does not disappear,

unplug the AC power cord, then plug it

back again.

If speaker wiring is not short-circuited,

contact your dealer.

Press POWER on the front panel to turn off

the unit. After unplugging the power cord,

consult your dealer.

Press SOUND or source selecting buttons

first, then press the button you want to use.

(See pages 40 and 41.)

Remove the obstruction.

Replace batteries.

Set RDS/DVD MENU mode selector to the

proper position.

POSSIBLE CAUSE

The power cord is not plugged in.

Speaker signal cables are not

connected.

An incorrect source is selected.

Muting is activated.

An incorrect input mode (analogue or

digital) is selected.

Connections are incorrect.

The balance is set to one extreme.

Incoming signal is too weak.

The station is too far away.

An incorrect antenna is used.

Antennas are not connected properly.

Ignition noise from automobiles.

Speakers are overloaded because of

high volume.

Speakers are overloaded because of

short circuit of speaker terminals.

The unit is overloaded because of a

high voltage.

The remote control is not ready for

your intended operation.

There is an obstruction hiding the

remote sensor on the unit.

Batteries are weak.

RDS/DVD MENU mode selector is set

to the wrong position.

Note:

When you use the digital coaxial connection, the sounds may be intermitted by the outside noise such as a lightning discharge but they will

restore automatically. This is not a malfunction.

Mastering Remote Operations/Troubleshooting

EN40-46.RX-E100RSL[B]_4 01.3.7, 8:34 PM45

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC RX-E100RSL Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC RX-E100RSL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info