Bedienungsanleitung Kalorik EXC SFC 2 (Seite 13 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

487434

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Team

International BELGIUM. The pages must be reproduced

and folded in order to obtain a booklet A5 (+/- 148.5 mm

width x 210 mm height). When folding, make sure you

keep the good numbering when you turn the pages of

the I/B. Don’t change the page numbering. Keep the

language integrity.

EXC SFC 2 - 110310

Assembly page 13/76

Fax +32 2 359 95 50

STORAGE OF ACCESSORIES:

In the base of the appliance there is a compartment in which you can store the accessories.

Separate the water tank from the base by pressing the button at the back of the appliance

near the right wheel and lifting the water tank upwards by the handle at the same time.

When you have stored the accessories or taken out the desired accessory, put the water tank

back on the base of the appliance. Press down firmly until it clicks into place.

OPERATION:

CAUTION! This appliance should not be used directly on soft plastics, non-pretreated wood or

cold glass.

Steam could damage the furniture surface. For a safe work please execute a test

run beforehand. Pay attention to the instructions for maintenance of the

manufacturer.

ASSEMBLY:

(DO NOT ATTACH THE APPLIANCE TO THE POWER SUPPLY UNTIL YOU HAVE CHOSEN AND

ATTACHED AN ACCESSORY.)

Warning! After use, unplug the appliance from the mains supply socket and press the steam

button to reduce the internal pressure sufficiently. Then you can release the safety cap.

1. Take the desired accessory from the storage compartment and put the water tank back

on the base of the appliance (see section “STORAGE OF ACCESSORIES”).

2. Attach the flexible hose with the steam gun to the appliance. To do so, flip down the flap

that covers the hose connection inlet and insert the hose connector into the hose

connection inlet until it locks, making sure that the small lug of the hose connector enters

into the small slot at the bottom of the hose connection inlet. You may press the release

buttons on the sides of the hose connector to facilitate the entering of the hose connector

into the hose connection inlet. To remove the hose after use, press the release buttons on

the sides of the hose connector and pull at the hose connector.

3. Unscrew the safety cap. To do so, press the safety cap and at the same time turn it

anticlockwise (if there is still water in the tank and if the safety cap was still screwed in tight

for a previous use, some degassing will occur. This is normal and not dangerous).

4. Fill the water tank with water. Please use the provided measuring cup and the funnel. Do

not exceed the maximum filling level (1.4 litres). If the water in your region is hard, it is

advisable to use distilled water or in that case you can also use tap water that has been

boiled beforehand.

5. Note: never fill descaling agent, perfume or detergent into the water tank, in order to

avoid damages to the appliance.

6. Screw back the safety cap. To do so, press the safety cap and at the same time turn it

clockwise.

7. If you want to clean floors or areas which are difficult to reach, assemble the extension

tubes. To do so, push the open end of a tube onto the steam gun until the release button

of the steam gun clicks into place. You can assemble just one, two or all three extension

tubes. To take the extension tubes off after use, press the release button on top of the

extension tube or steam gun and pull the tubes apart.

8. Put the floor brush on the extension tube until the release button clicks into place if you

want to clean floors. If you want to use another accessory, you first have to assemble the

accessory connecting piece: slide the accessory connecting piece onto the steam gun or

onto the extension tube until the release button clicks into place. Then assemble the

straight nozzle onto the accessory connecting piece and give the straight nozzle a quarter

turn in an anti-clockwise direction to lock it into place. To take the straight nozzle off after

use, give it a quarter turn in a clockwise direction and pull it off. To take the floor brush or

the accessory connecting piece off after use, press the appropriate release button and

pull it off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kalorik EXC SFC 2 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info