Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
WALL-MOUNTED SPLIT AIR CONDITIONER
INSTRUCTION MANUAL
Ref: 060210_GB
KA AC 26
230V~1040W
KA AC 27
230V~1740W
Thank you for choosing one of our air conditioners. Please read this INSTRUCTION
MANUAL carefully before using the appliance and keep it for further reference.
Contact our local qualified service center, who will install your appliance. This appliance
must be installed by a competent qualified technician. We will not be held responsible
for any services or costs if the units are not installed by a qualified technician.
Please always keep your outdoor unit in vertical position during handling.
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Inhalt der Seiten


  • Page 1

    WALL-MOUNTED SPLIT AIR CONDITIONER
    INSTRUCTION MANUAL
    Ref: 060210_GB

    KA AC 26
    230V~1040W

    KA AC 27
    230V~1740W



    Thank you for choosing one of our air conditioners. Please read this INSTRUCTION
    MANUAL carefully before using the appliance and keep it for further reference.



    Contact our local qualified service center, who will install your appliance. This appliance
    must be installed by a competent qualified technician. We will not be held responsible
    for any services or costs if the units are not installed by a qualified technician.



    Please always keep your outdoor unit in vertical position during handling.



  • Page 2

    CONTENTS

    P
    Contents ................................................................... 1
    2
    Safety Awareness .................................................................2
    Name of Parts ......................................................................4

    Operation procedure
    Remote Controller's Preparation Before Operation........................6
    Operation Explanations of Air Conditioner..................................

    7

    Service and Maintenance of the Air Conditioner.....................11
    11

    13
    Fault Confirmation and Analysis ...........................................13
    15
    Performance Parameters ....................................................15
    16
    Installation Explanations ......................................................16

    1



  • Page 3

    SAFETY AWARENESS
    Read and understand thoroughly this safety awareness before use.
    The items indicated here are very important safety precautions, which must be followed.

    Must connect grounding line

    Absolutely no

    Must unplug plug

    Must be done

    WARNING
    Do not pull power cable. Hold plug to unplug
    when removing power, or part of the line in
    the power cable may break and cause fire.

    Do not let cool air blow directly at you for long
    time.Possible health problems may occur.

    Do not connect at the middle of the power
    cable or extend it. Do not use multi - hole
    sockets. Possible fire electric shock may
    occur for poor connection,bad insulation and
    excessive allowable current.

    Do not plug power cable when in operation.
    (Spark may appear, and cause fire.) Pull the
    power plug out from the outlet or cut off the
    power supply when you don't use the air
    conditioner for a long time. (Accumulated dirt
    will cause fire.)

    Do not damage power cable, or do joining
    work.By putting stuffs on the power cable,
    heating it or do joining works,a possible short
    circuit may cause fire and electric shock.

    Provide a power outlet to be used exclusively
    for each unit, and a power supply disconnect
    and circuit breaker and current fuse protector
    should be provided in the exclusive line.

    2



  • Page 4

    SAFETY AWARENESS
    WARNING
    Clean the air conditioner with a soft and dry
    cloth. Do not use chemical solvent,insecticide,
    Inflammable-spraying material or which damage the appearance of air conditioner for cleaning.

    The appliance shall be installed in accordance
    with national wiring regulations.
    The appliance must not be installed in the laundry.
    The appliance must be installed 2.3m above
    the floor.
    The appliance must be positioned so that the
    plug is accessible.

    Do not put burning appliances at the place
    where can be blown directly by the air,
    insufficient burning may occur.

    Do not install the air conditioner where leak
    flammable gas. If there is electrical leakage
    accidentally from air conditioner, it is easy to
    cause fire or explosion ,as is very dangerous.

    Stop operation and unplug power cable immediately if abnormality is found ( burned smell
    etc ).

    Do not use for special purposes. Do not use to
    store precision equipment,food,painting etc, which are required humidity and temperature, for
    their quality may be affected.

    Close doors and windows ( better using contains )while operating air conditioner for a long
    time,if room air is quite turbid,you should open
    a door and window for a moment to get some
    outdoor fresh air.

    Do not operate air conditioner at COOL/DRY
    mode for a long time under high humidity
    ( above 80%), if door/window is open or under
    high humidity condition, condensation may
    drop from the unit.

    Do not install, service or move the Air Conditioner on your own. Improper process can cause fire,
    electric shock, the falling unit can injure people or water leakage. Contact our air conditioner specially
    engaged service center.

    3



  • Page 5

    NAME OF PARTS
    INDOOR UNIT
    Filter

    Front panel

    Power plug

    Air inlet

    RUN

    SLEEP

    TIME

    SWING

    MANUAL

    Left / Right deflector

    Deflector

    OPERATION
    MODE

    OFF

    ON

    TIME

    CANCEL

    Display

    Remote
    controller

    I/O

    SET

    FAN SPEED SLEEP

    Manual operation
    (open the Front panel)
    Sleep

    Run

    Check switch

    Emergency operation
    switch

    Ti m e r

    Time indicator
    Sleep indicator
    Run indicator

    OUTDOOR UNIT
    Air inlet

    Connecting pipe

    Drain hose
    Air outlet

    Drain opening

    4



  • Page 6

    NAME OF PARTS
    REMOTE CONTROLLER
    Signal ejecting window

    OPERATION
    DISPLAY

    SWING BUTTON

    SWING

    MANUAL

    OPERATION
    MODE

    TEMPERATURE
    ADJUSTMENT
    BUTTON

    OFF

    ON

    CANCEL

    FAN SPEED
    BUTTON

    I/O

    OPERATION MODE
    BUTTON
    TIME OFF
    BUTTON
    TIME ON
    BUTTON
    TIME CANCEL
    BUTTON

    TIME

    RUN/STOP
    BUTTON

    MANUAL SWING
    BUTTON

    SET

    FAN SPEED SLEEP

    TIME SET
    BUTTON
    SLEEP
    BUTTON

    RESET PIECE

    NOTICE
    cool only type hasn't HEAT mode

    5



  • Page 7

    REMOTE CONTROLLER PREPARATION
    1

    Open back cover, put in batteries.

    21

    Short RESET piece with forceps.
    ( Short two RESET piece after
    changing the batteries. )

    NOTICE
    If the remote controller can't be operated normally,
    short two RESET piece, it will operate normally.

    The signal can be reached within six metres directly
    in front of indoor unit.

    Handle remote controller carefully. Do not drop, throw and get
    wetted. Avoid malfunction.

    When the button is pressed, indoor unit will beep once or twice,
    indicating the receiving of the signal.If no beep is heard, press
    again.

    Remove batteries if Remote controller
    has not been used for a long time.

    6



  • Page 8

    OPERATION OF AIR CONDITIONER
    Operation procedure-Control under the Remote controller

    1

    Run/Stop
    Press I/O button, to start operation, and stop when repressed.

    21

    Temperature adjustment
    Press TEMPERATURE ADJUSTMENT Button,To decrease1 C by pressing
    button once.
    button once, And to increase 1 C by pressing
    Temperature change will be displayed in the remote controller's display.

    3

    Fan speed adjustment
    Press FAN SPEED button,to change the fan speed of indoor unit in the order of
    ( medium )
    ( high )
    ( auto ).

    4

    ( low )

    Sleep selection
    Press SLEEP button, set sleep operation, and cancel when repressed.
    During the night,there is sleep mode,which can adjust the temperature automatically and
    is more quiet.
    In cool mode,after sleep mode is set,Ts(temperature setting) will increase 1 in first hours,
    increase 2 in second hours and will operate as this temperature.
    In heating mode,when sleep mode is set,Ts will decrease 2 in the first hour,decrease 2
    more in the second hour and then operate as this temperature.
    Changing of operation mode will cancel sleep mode.

    51

    Air flow direction adjustment
    Change up/down air flow direction

    1 Press MANUAL button, the deflector will move to a specific angle. Change the deflector
    of indoor unit follow the order of

    NOTICE

    (2)

    In DRY or COOL mode , air blows downward in
    it will change to horizontal

    7

    (1)

    (3)

    (4),

    (4)

    (5) (Fig.2)

    (5) for one hour,then

    (1) blowing automatically to prevent dropping.



  • Page 9

    OPERATION OF AIR CONDITIONER
    2 Press SWING button, the deflector will start to operate.Press again the SWING button
    to stop at the position of the deflector set before.
    Change right/left air flow direction
    Manually swing Left/Right deflector,to change right/left air flow direction.Complete adjustment before operation, if adjusted during operation,the auto swinging deflector may
    pinch your fingers.(Fig. 1)

    ( Fig.1 )

    ADVICE

    In DRY or COOL mode, advise to adjust the
    Fan speed with (auto), air blows in (1).
    In HEAT mode, advise to adjust the Fan speed
    with
    (auto), air blows downward in (4)/ (5).

    COOL
    mode
    DRY
    mode

    (1)
    (2)
    (3)

    Adjust the up/down air flow with the remote
    controller,avoid turning deflector with hands
    to prevent injury.

    HEAT
    mode

    (4)
    (5)
    ( Fig.2 )

    8



  • Page 10



  • Page 11

    OPERATION OF AIR CONDITIONER
    71

    Timer operation
    Timer operation ON

    1 Press button

    ON

    if you want to set timer when air conditioner stops ,
    flickers on the Remote Controller display.

    of
    ¡±

    ¡±

    OFF

    Press button
    if you want to cut off timer when air conditioner operates , ¡± of
    ¡± flickers on the Remote Controller display.

    2 Press button

    ON

    OFF

    ON

    OFF

    or
    to enter time setting . press button
    or
    the timer will increase 1 hour, the time will be displayed on remote controller .

    3 Press button

    to fix time setting.
    Remote Controller display.

    or

    SET

    one time,

    will stop flickers on the

    Timer operation OFF
    If you want to switch off the timer operation, press button
    disappear on the remote controller display.

    CANCEL

    and

    or
    ¡
    ±

    will

    NOTICE
    1.If power sets off, time must be set again, otherwise, Timer operation will not run properly .
    2.If the air conditioner has been in “

    ”or
    ”mode time on or time off, but you want to
    ¡± “
    change the time, you must cancel the primary condition then set the new time condition,
    otherwise, error will incur.
    3.After having chosen the time mode, if you press the

    once incautiously, the setting
    SET

    time will count time anew automatically as primary setting time, and the display time will not
    change. So if you want air conditioner operate as primary setting time, you must set time anew.

    Operation procedure-Control under the Emergency operation switch
    In case the batteries in the remote controller are
    wore out, or remote controller is at fault, use emergency operation switch.( ).
    (Cool only type)
    Every time the switch is pressed, it changes in
    sequence of COOL
    STOP.
    (Heat pump type)
    Every time the switch is pressed, it changes in
    sequence of COOL
    HEAT
    STOP.

    Emergency run operation procedure as the following:
    Setting temperature

    Fan speed

    Deflector

    24 C

    High

    Swing

    10



  • Page 12

    11

    SERVICE AND MAINTENANCE
    Air Conditioner no use for a long time.

    1

    Start fan for 3-4 hours to completely dry the inside of the indoor unit.
    Set COOL mode or HEAT mode,
    and select the setting temperature, maximal.

    Want to use the Air Conditioner

    1

    ION
    ERAT

    Clean filters and replace them to original position.Clean indoor unit with soft
    clothe.
    Do not use gasoline, benzene, thinner,
    grinding powder, detergent,insecticide
    etc. to clean units as they can hurt the
    units.

    OP
    FAN

    2

    Turn off air conditioner, unplug the
    power plug,otherwise, the accumulated dirt may cause fire.

    2

    3

    Take the batteries out of the remote
    controller.

    3

    Inlets and outlets of indoor and outdoor units shall not be covered/blocked.

    Ground wire shall not be loose.
    Put in batteries in the remote controller,
    and plug the power plug.



  • Page 13



  • Page 14

    FAULT CONFIRMATION AND ANALYSIS
    If problems can not be solved after completing the following items,
    please stop the air conditioner, contact our air conditioner specially
    engaged service centre nearest to you to get help.
    Is there a fault ?
    Air conditioner does
    not operate at all.

    Remote controller is not
    available and does not
    display.

    It is not running
    after I/O button
    is pressed.

    Cooling and heating
    efficiency is not good.

    Fault analysis
    Does power fail ?
    Is plug out ?
    Does power fuse or switch off ?
    Is voltage higher than 253 V or lower than
    207V?
    Is the time operation correct?

    If disturbed abnormally or operation modes
    changed too frequently, sometimes the remote controller would lose function. Please
    plug out and plug in again.
    If remote controller displays unclear or displays all symbols, please change batteries.

    This is a way to protect compressor as per
    microprocessor instructions. Please wait 3
    minutes.

    Is temperature set suitably ?
    Are filters dirty?
    Are inlets and outlets of outdoor unit blocked?
    Does sleep function start during daytime?
    Does indoor fan speed set low ?
    Are doors and windows closed ?

    Air will not immediately
    blow out at the start
    of HEAT mode.

    13

    It is processing information, air will only blow
    out when sufficiently warm. Please wait.



  • Page 15

    FAULT CONFIRMATION AND ANALYSIS
    Is there a fault ?
    Indoor unit fan stops
    for about 10
    minutes during
    heating.

    Fault analysis

    It is defrosting of the outdoor unit coil.It should
    complete this process in about 10 minutes at
    most.( It freezes when outdoor temperature is
    low and humidity is high. )

    Issues cracking sounds

    The friction sounds caused by expansion and
    contraction of front panel resulting from temperature changes.

    You can hear the
    sound of running
    water

    It is the sound of expanding refrigerant inside
    the air conditioner.
    Sound of accumulated water dropping on the
    heat-exchanger.
    Melting sounds of frost on heat-exchanger.

    Indoor unit issue
    pooosh
    sound and click
    sound.

    Click sound of fan or compressor when switching ON/OFF.
    pooosh sound of refrigerant inside the air
    conditioner.

    There is odd odor
    in the air that air
    conditioner blow out.

    Outdoor unit leaks
    water.

    Air conditioner recycles should have absorbed
    odors from wall, carpet , furniture and cloth
    closet out into the air.

    During cooling, connecting pipe or pipe connector is cooled to form condensates.
    During heating or defrosting , melting water
    and water vapor will run out.
    During heating, water on heat-exchanger will
    drop.

    14



  • Page 16



  • Page 17

    INSTALLATION SKETCH
    Installation sketch
    At least 24mm or
    more from top

    Confirm installation place with
    the marker for indoor unit installation board.

    105m
    m or m
    ore
    from s
    ide wa
    ll

    above 7mm

    155m
    m or m
    ore
    from s
    ide wa
    ll

    Configuring pipe can be
    installed to back, right,
    underside, or left-back
    side.
    front
    back
    right
    left
    back
    underside left-back

    above 100mm

    Abov

    e 10

    abo

    0mm

    Notice: Do not put the
    drain hose high.

    Cover connecting pipe with
    heat-isolating material.

    ÔÉmÏm
    m
    10Ò0
    m
    e
    v
    0
    a1b0o

    m
    00m
    5
    e
    v
    abo
    ve 3
    50m
    m

    the thickness of heatisolating material is
    8mm.
    When installing connecting pipe on
    the wall & metallic net or thin armor
    plate, please put the 20mm or more
    thickness wooden block between
    the wall and connecting pipe or wape
    the connecting pipe by 7 to 8 layers
    bonding tape.

    16



  • Page 18

    INSTALLATION ACCESSORIES
    Installation Instructions

    1

    Location of indoor unit
    Cooled or heated air should be blown
    to every part of the room.
    Maximum height between indoor/outdoor units is 5m.
    Mount on firm wall to avoid any vibration.
    Avoid direct sunshine.
    Easy to drain condense water.
    Far away from the fluorescent lamp, it
    may effect the remote control function.
    Minimum distance between air conditioner and home appliance( TV/ Radio
    etc. ) is 1m.

    17

    2

    Location of outdoor unit
    Airflow can not be blocked.
    Good ventilation, low dust,avoids rain
    or direct sunshine.
    Operation noise or air blowing out will
    not affect neighbors' comfort.
    Firmly mounted on rack,which will reduce noise and vibration.
    Avoid places to the flammable gas
    leakage area.
    Unit must be mounted firmly when
    installed high up.
    Not to be affected by strong wind.



  • Page 19

    INSTALLATION
    INDOOR UNIT

    1

    Secure the mounting plate
    The mounting plate should be attached to the structural part of wall (post etc.).
    fasten string at the central hole
    at least 24mm
    155mm or more
    from sidewall

    105mm or more
    from sidewall

    tappping screw
    ST4 25(5)

    NOTICE

    2

    mounting plate

    plumb

    The holes at solid arrow position must be secured to avoid the shake of mounting plate.
    When the expansion bolts are used, two holes ( 11 20 or 11 26 ) that the distance
    between them is 450mm should be adopted.

    Drill on the wall

    40mm

    fasten string at the central hole

    Center of hole( 65mm)

    plumb

    120mm

    Pipe hole
    Center of hole( 65mm)

    Confirm the position of holes, and drill holes of

    3

    65mm on the wall.

    Connect the cable

    Joint the outdoor and indoor
    power cable fast connector

    Fix screw

    Outdoor power cable fast connector

    Indoor power cable fast connector

    Fix the outdoor cable with
    screw(see fig)

    Indoor power cable
    Outdoor power cable

    18



  • Page 20

    19

    INSTALLATION
    NOTICE

    The wires have been connected
    before. If there is any looseness,
    please connect the cable according the below processes.

    Electrical box cover
    Screw
    Indoor unit
    terminal

    1 Open the front panel;
    2 Remove the screw from electrical box cover, pull the
    electrical box cover away from the unit and set aside.
    3 Remove the screw from fastener, pull the fastener
    away from the unit and set aside.
    4 Connect the cable.
    5 Replace the fastener and electrical box cover.

    Fastener
    Pull the connecting cable's
    wire in completely

    Diagram

    Connecting cable

    Screw

    Indoor unit terminal

    41

    Connecting cable

    Installation drain hose
    liquid pipe

    1 NOTE:
    The drain hose must be arranged beneath the copper pipe.
    The drain hose must not be hunched or bended.
    Do not wrap the drain hose by pulling it.
    When the drain hose must pass through indoor, it should be
    wrapped by the special heat insulated materials.
    The copper pipe and the drain hose must be wrapped by felt
    strip. Heat insulated pad should be used between the connecting
    pipe and the wall.

    gas pipe

    drain hose
    adiabatic
    underlay
    felt

    2 ROUTE OF PIPE
    If pipe came out of the right side of the indoor unit, cut part
    1 on the unit;
    If pipe came out of the lower-right side of the indoor unit, cut part "2" on the unit;
    If pipe came out of the left side of the indoor unit, cut part 3
    on the unit.

    1
    2

    3

    3 REFIT OF DRAIN HOSE
    If pipe comes out of the left side of the indoor unit,the drain hose
    must be refit, otherwise water leakage may occur.
    Refit methods: Interchange the position of drain hose and drain
    rubber bib, the right diagram is before refit.
    Clearance is not allowed after refit, it would lead to water leak.

    51

    drain hose

    drain rubber
    bib

    Installation indoor unit

    Let pipe go through the wall hole and attach
    the indoor unit to the mounting plate.(Locate
    the rib of indoor unit in the hole of the mounting plate.)

    Indoor unit

    Bottom

    the mounting plate

    the rib of indoor unit



  • Page 21

    INSTALLATION
    61

    Arrangement of drain hose

    To eject the condense water easily, the drain hose should be declined downward.
    The arrangement in diagram2-5 is wrong.
    decline
    downward

    decline
    downward

    standing
    water
    dip hose in water

    air
    water
    leak
    (Fig. 1)

    water
    leak
    (Fig. 2)

    50mm or less
    from floor
    (Fig. 5)

    (Fig. 3)

    (Fig. 4)

    drain hose

    If the drain hose connected with the indoor unit is short, it can
    be extended by the hose in the accessory box.
    When the drain hose must pass through the indoor, it should be
    wrapped by the special heat insulated materials.

    71

    hose(ID 15cm)
    PVC hard

    Seal of wall hole and fasten of pipe
    Use putty to seal the
    wall hole.
    Use clamp ( pipe fastener ) to secure
    the pipe at specified
    position.

    get rid of unwanted part
    clamp

    airproof with putty
    clip the connecting pipe with clamp

    screw

    indoor unit

    OUTDOOR UNIT

    1

    Connect the cable

    Connect diagram

    Outdoor unit terminal

    2N

    N234

    Connecting
    cable

    Indoor unit terminal
    Connecting
    joint
    Connecting Brown
    cable
    Blue
    Yellow/Green
    Black

    Brown
    Blue

    N2

    N23

    4

    Yellow/Green
    Gray
    Brown
    Blue
    R1R2

    Outdoor unit terminal
    Cool only type

    WARNING

    Heat pump type

    The connecting cables must be clipped together.
    Special cable must be used to connect indoor unit and outdoor
    unit. It should be ensured that the terminals are not influenced by
    external force. Poor connect may cause fire.
    The electric box cover must be mounted and secured in position,
    otherwise fire or electrical shock may occur because of dust or
    moisture.
    AUS-12HR53CA2(fast connecting) can be connected only to a supplyed with
    system impedance no more than 0.323 ,In case necessary, please consult
    your supply authority for system impedance information.

    20



  • Page 22



  • Page 23

    INSTALLATION
    31

    Add refrigerant

    If the refrigerant leaks or is not enough ,add refrigerant as the below processes.
    Connect charging hose(low pressure) of manifold
    gauge to the service port of gas shut-off valve. (Fig.1)

    Manifold gauge

    Pressure meter
    High pressure
    valve

    Low pressure
    valve

    Open the valve of the low pressure and close high
    pressure valve of manifold gauge.
    Purge the air from the system using the vacuum pump
    until its pressure(low pressure side) is below 12Pa.

    Charging line

    Close the low pressure valve and remove the charging
    hose from service port .

    Vacuum
    pump

    Service port

    (Fig.1)

    Turn the gas shut-off valve of outdoor unit to close, connect charging
    hose(low pressure) to the service valve, then open gas shut-off valve
    of outdoor unit again. (Fig.2)
    Connect refrigerant bottle to charging hose, convert it,
    then fill liquid refrigerant as the rating label.
    R407C

    Close the gas shut-off valve, disconnect the manifold gauge,
    and open gas shut-off valve again.

    liquid shut-off valve
    gas shut-off
    valve

    Tighten nuts and cap of each valve.
    NOTICE

    Do not let gas refrigerant into the system.

    Service port

    (Fig.2)

    Install the drain joint(only for heat pump type)
    Install the double-channel drain joint in the hole
    of outdoor unit's bottom, then connect drain hose and joint.
    Bottom

    Test

    double-channel
    Drain hose
    drain joint

    Having accomplished air installation and leak test , test operation must be done. Before test operation,
    wiring safety inspect must be carefully done.
    Test operation procedure:
    Only can check switch be done, and remote controller can not.
    1.Connects system with power plug, and open front panel.
    2.Press check switch, then system operates as test.
    3.If the indicate lamps light first, go out in succession, the system
    is normal, otherwise, there has lamp flashing indicating that
    system has wrong. Please check system for once.

    22



  • Page 24

    PROTECTION OF THE ENVIRONMENT– DIRECTIVE 2002/96/EC
    In order to preserve our environment and protect human health, the waste electrical and
    electronic equipment should be disposed of in accordance with specific rules with the implication
    of both suppliers and users. For this reason, as indicated by the symbol
    on the rating label or
    on the packaging, your appliance should not be disposed of as unsorted municipal waste. The
    user has the right to bring it to a municipal collection point performing waste recovery by means
    of reuse, recycling or use for other applications in accordance with the directive.






Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kalorik ka ac 27 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Holen Sie sich Ihr Benutzerhandbuch per E-Mail

Geben Sie Ihre E-Mail-Adresse ein, um das Handbuch zu erhalten von Kalorik ka ac 27 in der Sprache / Sprachen: Englisch als Anhang in Ihrer E-Mail.

Das Handbuch ist 2,26 mb groß.

 

Sie erhalten das Handbuch in Ihrer E-Mail innerhalb von Minuten. Wenn Sie keine E-Mail erhalten haben, haben Sie wahrscheinlich die falsche E-Mail-Adresse eingegeben oder Ihre Mailbox ist zu voll. Darüber hinaus kann es sein, dass Ihr ISP eine maximale Größe für E-Mails empfangen kann.

Andere Handbücher von Kalorik ka ac 27

Kalorik ka ac 27 Bedienungsanleitung - Deutsch - 24 seiten

Kalorik ka ac 27 Bedienungsanleitung - Holländisch - 24 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info