478067
9
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
This mode is used to decrease the humidity in the room.
O O
The temperature setting are adjustable between 16 C to 30 C . Cooling begins
O
automatically when the room temperature is 1 C above the set point, and stops
O
when the room temperature is 1 C below the set point. The fan will not stop running.
O O
The temperature settings are adjustable between 16 C to 30 C in heating mode.
the fan speed is optional.
When heating stops, there may be a slight delay of 30 seconds for the fan
For the cooling only models, after selecting "AUTO" by "MODE" keypad,the unit
will select the appropriate operating mode from "FAN", "COOL" or "DRY" based upon
the temperature difference between the actual and desired room temperature.
For the cooling and heating models,after selecting "AUTO" by "MODE" keypad,the
unit will select the appropriate operating mode for Cool, Heat or Dry based upon the
temperature difference between the actual and desired room temperature.The default
is 20
o
C,the default cooling temperature set point is 25
o
C.
motor to stop.
Note: This Function can only be activated by remote control, Please refer to remote
operating instruction for more detail information
heating temperature set point
FILTER:
This feature is a reminder to clean the Air Filter (See Air Filter) for more efficient
operation.The light will illuminate after 250 hours of operation.To reset after cleaning
the filter, press the "FILTER" button and the light will go off.
DEFROST:
Under heating mode, when there is "H1" on the LED display indicates the unit is under
defrost function. In this case, any set on main unit or remote controller will not be
carried out until the defrost is completed.
FAILURE INDICATOR DISPLAY:
Indicates a malfunction of the indoor room temperature sensor
Indicates a malfunction of the evaporator temperature sensor
Indicates a malfunction of the outdoor condenser temperature sensor
When one of the above malfunctions occurs, turn off the unit, and check for
any obstructions. Restart the unit, if the malfunction is still present, turn off
the unit and unplug the power cord. Contact the manufacturer or its service
agents or a similar qualified person for service.
F 1F 1
F 2F 2
F 4F 4
8
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kelvinator KWH20HRC wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info