686283
8
Zoom out
Zoom in
Vorherige Seite
1/12
Nächste Seite
Cool X
6
EN
FastMig X
The factory default setting for FastMig Pulse is AUTO. If a cooling unit is not connected and
the operator tries to establish air-cooled operation together with an air-cooled gun, Err 27
is displayed. To establish air-cooled operation, select cooler ‘OFF’. This is done in the ‘System
Cong Menu as follows: Press the Menu button on the X 37 power source panel. Move the
menu display arrow (via panel's left-hand up-down arrow keys) to select ‘System Cong Menu
and then press the select button. Choose Water Cooling:Auto and change via control knob to
setting Water Cooling:OFF’, then press Back/Exit. Cooler will then be set to the ‘OFF’ state for
air-cooled operation. Reset power source via on/o switch and continue welding.
When selected, the operation of the cooling unit is automatic, starting when welding
commences. When welding stops the pump will continue operation for approx. 5 min, so
reducing the gun and the cooling liquid to ambient temperature.
After completing the preparations explained above, the device is ready for welding. Before
welding, read the operating instructions.
3. OPERATION
3.1 Cooler operation
See also 2.4.2. Main parts of cooling unit
The Cool X cooler operation is controlled by the microprocessor of the power supply. The
cooler pump starts to operate when the welding begins. After the welding has stopped, the
pump will operate 1 to 5 minutes longer depending on the welding time. During this time the
liquid will cool down to the ambient temperature and cools down the welding gun.
Check the tank liquid level regularly and add liquid, if necessary.
If the tanks coolant liquid level runs low, welding is stopped and an error code appears on the
FastMig panel. See trouble-shooting 4.3.
3.2 Overheat signal lamp
The overheat signal lamp is lighting when temperature control of the machine has detected
cooling water overheat. The ventilator cools down the machine and when the lamp goes out
welding can be started again.
3.3 Storage
The machine must be stored in a clean and dry room. Protect the machine from rain and keep
it away from direct sunshine in places where temperature exceeds +25° C. Check that there is
free space in front of and behind the machine for air circulation.
8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kemppi Cool X wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Kemppi Cool X

Kemppi Cool X Bedienungsanleitung - Deutsch - 12 seiten

Kemppi Cool X Bedienungsanleitung - Holländisch - 12 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info