686414
17
Zoom out
Zoom in
Vorherige Seite
1/30
Nächste Seite
15
© Kemppi Oy / 1515
EN
DOUBLE PULSE MIG
WFSpeed
0.7…25 m/min * Sets the wire feed speed.
Changes by steps of 0.05, when WFSpeed < 5 m/min, and
by 0.1, when WFSpeed > 5 m/min
WFS-Max
Sets the limit for maximum WFSpeed
WFS-Min
Sets the limit for minimum WFSpeed
FineTuning
-9.0…+9.0 Factory setting is 0.0
( = curve point)
Adjusts the base current of the curve (arc length) in
certain limits
FineTuningMax
-9.0…+9.0 Step: 0.5 Sets the limit for maximum arc length
FineTuningMin
-9.0…+9.0 Step: 0.5 Sets the limit for minimum arc length
Dynamics
-9…+9 Factory setting is 0 Controls the short circuit behaviour of the arc. The lower
the value the softer the arc is. The higher the value the
rougher the arc is.
Pulse Current
-10…+15% Factory setting
is 0%
Reduces (-) or raises (+) the pulse current of the curve
DPulseAmp
0.1…3.0 m/min Factory setting is
CURVE
Adjusts the amplitude of the WFSpeed by steps of 0.1.
Value comes from welding program.
DPulseFreq 0.4…8.0 Hz Factory setting is
CURVE
Adjusts the frequency of the double pulse by steps of 0.1.
Value comes from welding program.
WISEROOT+
WFSpeed
1.5…8.0 m/min * Sets the wire feed speed.
Changes by steps of 0.05, when WFSpeed < 5 m/min,
and by 0.1, when WFSpeed > 5 m/min
WFS-Max
Sets the limit for maximum WFSpeed
WFS-Min
Sets the limit for minimum WFSpeed
FineTuning
-9.0…+9.0 Factory setting is 0.0
( = curve point)
Adjusts the base current of the curve (heat of the arc)
within certain limits.
FineTuningMax
-9.0…+9.0 Step: 0.5 Sets the limit for maximum heat of the arc
FineTuningMin
-9.0…+9.0 Step: 0.5 Sets the limit for minimum heat of the arc
* Dierent welding programs may further restrict the value range.
WISETHIN+
WFSpeed
0.7…25 m/min * Sets the wire feed speed.
Changes by steps of 0.05, when WFSpeed < 5 m/min, and
by 0.1, when WFSpeed > 5 m/min
WFS-Max
Sets the limit for maximum WFSpeed
WFS-Min
Sets the limit for minimum WFSpeed
FineTuning
-9.0…+9.0 Factory setting is 0.0
( = curve point)
Adjusts the arc voltage of the curve (arc length) within
certain limits
FineTuningMax
-9.0…+9.0 Step: 0.5 Sets the limit for maximum arc length
FineTuningMin
-9.0…+9.0 Step: 0.5 Sets the limit for minimum arc length
Dynamics
-9…+9 Factory setting is 0 Controls the short circuit behaviour of the arc. The lower
the value the softer the arc is. The higher the value the
rougher the arc is.
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kemppi FastMig X 350MV wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info