686381
10
Zoom out
Zoom in
Vorherige Seite
1/26
Nächste Seite
EN
2.1.7 Starting the power source
Start the power source by turning the main switch A2 on the front panel to the I position. The
standby indicator A3 turns on.
NOTE! Always turn the device on and o using the main switch, not via the mains socket.
The cooling fan is started for a moment when the main switch is turned to the ‘I’ position. The
fan turns o after a while and then restarts during welding when the machine has warmed up
suciently. The fan continues running even after up to 10 minutes of welding, depending on
the temperature of the machine.
2.1.8 Power source indicators
The following indicators can be found on the front panel of the power source:
• When the green mains indicator A3 is on, the power source is in standby mode. This
indicator is on when the machine is connected to the mains supply with the main switch
in the ‘I’ position.
• When the yellow overheating indicator A4 is on, the machine has overheated. When the
indicator turns o, the machine can be used again.
• When indicator A4 blinks, the machine has encountered a failure. Attempt to remedy the
problem according to the instructions in Section 4, Troubleshooting. If the failure cannot
be eliminated, turn o the machine, and turn it on again. If the failure persists, write
down any fault code that may be shown on the display and contact authorised Kemppi
service agent.
2.2 CONTROL PANEL
2.2.1 Control panel parts
P2
P6P11 P13P5P3 P4
P9 P10
P8
P7
The control panel is used for controlling and monitoring the operation of the power source
and the wire feeder. The buttons are used for adjusting functions. The displays and indicators
reect the operating modes of the machine.
8
KempArc SYN 300, 400, 500, DT 400 / © Kemppi Oy / 1117
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kemppi Kemparc SYN 300 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info