Zoom out
Zoom in
Vorherige Seite
1/26
Nächste Seite
Operating manual
Käyttöohje
Bruksanvisning
Bruksanvisning
Brugsanvisning
Gebrauchsanweisung
Gebruiksaanwijzing
Manuel d’utilisation
Manual de instrucciones
Instrukcja obsługi
Инструкции по эксплуатации
Manual de utilização
Manuale d’uso
操作手册
EN
FI
SV
NO
DA
DE
NL
FR
ES
PL
RU
PT
IT
ZH
MinarcMig
Evo 170, 200
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Inhalt der Seiten


  • Page 1

    MinarcMig
    Evo 170, 200

    Operating manual
    Käyttöohje

    EN
    FI

    Bruksanvisning

    SV

    Bruksanvisning

    NO

    Brugsanvisning

    DA

    Gebrauchsanweisung

    DE

    Gebruiksaanwijzing

    NL

    Manuel d’utilisation

    FR

    Manual de instrucciones

    ES

    Instrukcja obsługi

    PL

    Инструкции по эксплуатации

    RU

    Manual de utilização

    PT

    Manuale d’uso
    操作手册

    IT
    ZH



  • Page 2



  • Page 3

    OPERATING MANUAL
    English

    © Kemppi Oy / 1340



  • Page 4

    CONTENTS
    1.

    Preface.................................................................................................................. 3
    1.1 General. ............................................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
    1.2 Product introduction. .................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
    1.2.1 Properties. ................................. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
    1.2.2 About welding. ......................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
    2.

    EN

    Before you start using the unit.................................................................... 4

    2.1 Unpacking. ......................................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
    2.2 Positioning and location of the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
    2.3 Distribution network...................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
    2.4 Serial number.................................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
    2.5 General view of the machine. ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
    2.6 Cable connections. ......................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
    2.7 Filler wire............................................. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
    2.7.1 Changing the feed roll groove.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
    2.7.2 Loading and threading the filler wire.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
    2.7.3 Reversing polarity..................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
    2.8 Controls and indicator lights....... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
    2.8.1 Display in automatic mode. ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
    2.8.2 Welding power adjustment in automatic mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
    2.8.3 Arc length trimmer in automatic mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
    2.8.4 Display in manual mode. ......... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
    2.8.5 Adjustments in manual mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
    2.9 MIG/MAG welding........................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
    2.10 Using the shoulder strap. ............. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

    3. Maintenance..................................................................................................... 17

    3.1 Daily maintenance. ......................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
    3.2 Maintenance of the wire feed mechanism. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
    3.3 Troubleshooting. ............................. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
    3.4 Storage. ............................................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
    3.5 Disposal of the machine............... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

    4.
    5.

    2

    Ordering numbers.......................................................................................... 20
    Technical data.................................................................................................. 21

    MinarcMig Evo 170, Evo 200



  • Page 5

    1.

    PREFACE

    1.1 General
    Congratulations on choosing MinarcMig Evo welding equipment. Used correctly, Kemppi
    p°roducts can significantly increase the productivity of your welding, and provide years of
    economical service.
    This operating manual contains important information on the use, maintenance and safety of
    your Kemppi product. The technical specifications of the equipment can be found at the end
    of the manual.
    Please read the manual carefully before using the equipment for the first time. For your
    own safety and that of your working environment, pay particular attention to the safety
    instructions in the manual.
    For more information on Kemppi products, contact Kemppi Oy, consult an authorised Kemppi
    dealer, or visit the Kemppi web site at www.kemppi.com.
    For Kemppi’s standard safety instructions and warranty terms and conditions, please visit our
    web site at www.kemppi.com.
    The specifications presented in this manual are subject to change without prior notice.
    NOTE! Items in the manual that require particular attention in order to minimise damage and

    EN

    personal harm are indicated with this symbol. Read these sections carefully and follow their
    instructions.

    Disclaimer
    While every effort has been made to ensure that the information contained in this guide
    is accurate and complete, no liability can be accepted for any errors or omissions. Kemppi
    reserves the right to change the specification of the product described at any time without
    prior notice. Do not copy, record, reproduce or transmit the contents of this guide without
    prior permission from Kemppi.

    1.2 Product introduction
    MinarcMig Evo 170 and 200 are easy-to-use MIG/MAG welding machines suitable for
    professional industry, site and repair welding. Before use or doing any maintenance work on
    the machine, read the operating manual and keep it for further reference.
    MinarcMig Evo tolerates input voltage fluctuation and is suitable for work on sites using
    power generators and use with long power cables. The power source utilises PFC technology,
    ensuring optimum usage on single phase power supplies. The IGBT inverter design delivers
    reliable arc ignition and welding performance, with all filler wire types.
    Welding and earth return cables are supplied in the delivery package, including gun, earth
    clamp and connections.

    1.2.1 Properties
    The welding machine is small, efficient and light. It is easy to carry with the handle or shoulder
    strap. It is suitable for a wide range of welding applications, and the possibility to use long
    power extension cables makes it easy to use in worksite conditions. It is also suitable for use
    with power generators.
    The MinarcMig Evo 170 is set manually, with separate control for wire feed speed and voltage.
    MinarcMig Evo 200 machine has both an automatic and manual operation mode. In the
    automatic mode, you must first select the filler wire material after which the welding voltage
    and wire feed speed can be adjusted with one control knob, according to the thickness of
    the sheet to be welded. Thus, selecting the right parameters is easy. In automatic mode, the
    length of the arc, or welding heat, is trimmed with another control. In manual mode, the
    welding voltage and wire feed speed are adjusted separately with their own controls. The
    use of the machine is aided with an LCD display which indicates the welding current, welding
    voltage and wire feed speed.

    © Kemppi Oy / 1340

    3



  • Page 6

    You can use steel (solid or cored wire), stainless steel, aluminium and CuSi as filler wire in the
    machine. The steel wire can be 0.6 mm, 0.8 mm, 0.9 mm or 1.0 mm thick, but the machine’s
    welding properties are optimum with a steel wire of 0.8 mm diameter. The stainless steel wire
    can be 0.8 mm, 0.9 mm or 1.0 mm in diameter, the aluminium wire 1.0 mm and CuSi wire 0.8,
    0.9 and 1.0 mm.

    1.2.2 About welding
    In addition to the welding machine, welding outcome is influenced by the work piece to be
    welded, welding technique and the welding environment. Therefore, recommendations in this
    manual must be followed.
    During welding, an electric welding circuit is created between the positive and negative
    poles of the machine. On delivery, the welding gun is connected to the positive pole of the
    machine terminals. The terminals are located inside the case door and should not be changed
    unless you intend to run a filler wire that is directed to be used in reverse polarity, electrode
    negative. When a filler wire is loaded to the machine, the wire feed mechanism drives the filler
    wire through the contact tip mounted in the welding gun, and thus transfers electrical power
    from the contact tip to the filler wire. The earth return clamp and cable (already connected to
    the machine on delivery to the negative terminal) connects to the workpiece to be welded.
    When the filler wire touches the work piece a short circuit occurs, forming the needed closed
    electrical circuit, an arc is formed and welding commences. Unrestricted current flow is
    possible only when the earth return clamp is properly attached to the workpiece and the
    fixing point of the clamp to the workpiece is clean, and free from paint and rust.
    Shielding gas must be used during welding in order to prevent air from mixing with the weld
    pool. Pure carbon dioxide or a mixture of argon and carbon dioxide is a suitable shielding
    gas for steel filler wire. Argon + 2 % CO₂ mixture is suitable for stainless steel wires. Argon is
    suitable for welding aluminium and CuSi wires. Some filler wires (referred to as self shielded)
    form a gas shield from the burning composition of the wire’s core, thus eliminating the need
    for a separate shielding gas supply.

    EN

    2.

    BEFORE YOU START USING THE UNIT
    NOTE! Please read the separate safety instruction booklet provided before you commence welding.
    Pay particular attention to the risks associated with fire and explosion.

    2.1 Unpacking
    When machine leaves factory, it is set up for use with 0.8 mm diameter filler wire. If you wish
    to use an alternative thickness filler wire or type, make sure that you suitably adjust the feed
    roll groove, welding gun contact tip and machine polarity for the material type selected.
    If you mainly use aluminium or stainless steel filler wire, we recommend you change the wire
    liner to a Kemppi plastic type, which is better suited for the material.
    Always before using the equipment, make sure it was not damaged during transportation.
    Also check that you have received what you ordered and that there are instructions for it.
    The packaging material of the products is suitable for recycling.
    Transportation
    The machine should be transported in an upright position.
    NOTE! Always move the welding machine by lifting it from the handle. Never pull it from the
    welding gun or other cables.

    Environment
    The machine is suitable for both indoor and outdoor use, but it should be protected from rain
    and sunshine. Store the machine in a dry and clean environment and protect it from sand and
    dust during use and storage. The recommended operating temperature range is -20…+40 °C.
    Place the machine in such a way that it does not come in contact with hot surfaces, sparks and
    spatters. Make sure the air flow in the machine is unrestricted.

    4

    MinarcMig Evo 170, Evo 200



  • Page 7

    2.2 Positioning and location of the machine
    Place the machine on a firm, dry and level surface. Where possible, do not allow dust or other
    impurities to enter the machines cooling air flow. Preferably site the machine above floor level;
    for example on a suitable carriage unit.
    Notes for positioning the machine
    • The surface inclination should not exceed 15 degrees.
    • Ensure the free circulation of the cooling air. There must be at least 20 cm of free space in
    front of and behind the machine for cooling air to circulate.
    • Protect the machine against heavy rain and direct sunshine.
    NOTE! The machine should not be operated in the rain as the protection class of the machine,
    IP23S, allows for outside preserving and storage only.
    NOTE! Never use a wet welding machine.
    NOTE! Never aim metallic grinding spray/sparks towards the equipment.

    2.3 Distribution network
    All regular electrical devices without special circuits generate harmonic currents into
    distribution network. High rates of harmonic current may cause losses and disturbance to
    some equipment.
    MinarcMig Evo 170 and 200 comply with IEC 61000-3-12.

    EN

    2.4 Serial number
    The serial number of the unit is marked on the rating plate. The serial number makes it
    possible to trace product manufacturing series. You might need the serial number when
    placing spare parts orders or when planning maintenance.

    2.5 General view of the machine

    2.
    3.
    1.

    5.

    4.

    1.
    2.
    3.
    4.
    5.

    Supply voltage cable
    Main switch
    Shielding gas hose connector
    Welding gun and cable
    Earth return clamp and cable

    © Kemppi Oy / 1340

    5



  • Page 8

    2.6 Cable connections
    Connection to the mains
    The machine is fitted with a 3 m long supply voltage cable and plug. Connect the supply
    voltage cable to the mains. Should you need to fit an alternative plug or mains cable, ensure
    installation is completed by an authorised electrician.
    NOTE! The fuse size needed is 16 A delayed.

    If you use an extension cable, its cross-sectional area should be at least as large as the
    machines supply cable (3 x 1.5 mm²). It is recommended to use 3 x 2.5 mm² extension cable.
    The maximum length for the extension cable is 100 meters.
    The machine can also be used with a generator. The minimum power for the generator is
    4.2 kVA, and the recommended power 8.0 kVA in order for the machine to be used at
    maximum capacity.
    Earth return
    The welding circuit earth return cable is already connected to the machine. Clean the
    workpiece surface and fix the earth return clamp to the work piece in order to create a
    welding circuit.

    EN

    Welding gun
    The welding gun is already connected to the machine. The filler wire, shielding gas and
    electric current is delivered to the weld inside the welding gun cable. When you press the gun
    trigger, shielding gas starts to flow and filler wire feed begins. The arc ignites when the filler
    wire touches the work piece. Inside the gun cable there is a factory-installed wire liner that
    is best suited for welding with steel and CuSi filler wires. It can temporarily be used also with
    stainless steel and aluminium wires. However, this is not recommended because of greater
    friction and reduced welding performance, and it may finally lead into failure of filler wire
    delivery.
    If you mainly use aluminium or stainless steel filler wire, we recommend that you replace the
    wire liner with a Kemppi plastic type, which is better suited for the material. For instructions
    on how to change the wire liner, please refer to the Maintenance section later in this manual.
    The gun neck can be rotated 360° to suit different welding positions. The neck is connected via
    a standard clockwise screw thread. Always make sure that the neck is almost fully connected
    to the bottom thread. This prevents damaging and overheating the neck.
    NOTE! If you intend to use other than 0.8 mm diameter steel filler wire, change the welding gun
    contact tip, gun liner, and drive roll to match the selected filler wire type and thickness.

    6

    MinarcMig Evo 170, Evo 200



  • Page 9

    Shielding gas
    Shielding gas is used for replacing air around the welding arc. For steel wires, use CO₂ (carbon
    dioxide) or a mixture of Ar (argon) and CO₂ for shielding gas. Welding performance will be
    improved when using mixed gas products. For stainless steel wires, use mixture of Ar and
    CO₂ (2 %), and for aluminium and CuSi wires, use pure argon. The required flow rate of the
    shielding gas is determined by the thickness of the welded sheet and the used welding power.
    The machine is delivered with a 4.5 m long gas hose. Connect the supplied female snap
    connector of the gas hose to the machine’s male connector. Connect the other end of the gas
    hose to the gas cylinder via a suitable and approved single stage regulator valve, where outlet
    flow rates can be adjusted.
    NOTE! Never attempt to connect directly to a compressed gas cylinder. Always use an approved
    and tested regulator and flow meter.

    1.
    20

    2.

    EN

    15
    10

    3.

    5
    l/min

    4.

    Connecting the gas hose to a typical welding regulator control valve
    1. Connect the hose to the welding machine snap connector
    2. Open the regulator valve of the gas cylinder
    3. Measure the gas flow
    4. Adjust the flow with the adjustment knob (10–15 lpm)
    NOTE! Use a suitable shielding gas for the welding application. Always secure the gas cylinder in an
    upright position with either a specially made wall rack or cylinder trolley. Always close the cylinder
    valve after welding.

    © Kemppi Oy / 1340

    7



  • Page 10

    2.7 Filler wire
    The machine is delivered with the welding gun connected to the positive pole (+) making it
    suitable for welding with solid steel, stainless steel, aluminium and CuSi filler wires without
    extra adjustments.

    2.7.1 Changing the feed roll groove
    When the machine leaves factory, the feed roll groove is set for welding with filler wires of
    0.8–1.0 mm diameter. The feed roll groove must be changed, if you use 0.6 mm thick filler wire.
    Changing the feed roll groove

    5., 8.

    6.

    EN
    1., 9.
    3.
    2., 4.
    7.

    1.
    2.
    3.
    4.
    5.
    6.
    7.
    8.
    9.

    8

    Release the pressure control lever.
    Switch the machine on from the main switch.
    Press the welding gun trigger and drive the feed roll in such a position that the locking screw
    is clearly visible and can be accessed.
    Switch the power off from the main switch.
    Release the feed roll locking screw with a 3.0 mm Allen wrench approximately half a
    turn.
    Pull the feed roll from its shaft.
    Turn the feed roll around and reinstall it to the shaft all the way to the bottom stop, making
    sure that the screw is parallel to the flat area ground onto the shaft.
    Tighten the feed roll locking screw.
    Close the pressure control lever.

    MinarcMig Evo 170, Evo 200



  • Page 11

    2.7.2 Loading and threading the filler wire
    1., 10.

    1.

    Open the filler wire cabinet door by pressing the orange door latch button and installing
    the filler wire spool in such a way that it rotates counter clockwise. You can use either a
    5 kg (diameter 200 mm) or 1 kg (100 mm) filler wire spool with MinarcMig Evo by adding
    or removing the 200 mm spool adapter.
    5 kg

    EN

    2.

    1 kg
    2.

    2.
    3.
    4.
    5.

    Attach the wire spool friction plate, lock and secure the spool.
    Release the filler wire end from the spool, but carefully holding on to it all the times.
    Straighten the wire end for approximately 20 cm and cut the wire in the middle of the
    straightened section.
    Smooth the sharp filler wire end
    5.

    © Kemppi Oy / 1340

    9



  • Page 12

    7.

    9.
    5., 8.
    6.
    7.
    8.

    EN

    Open the pressure control arm which then opens the feed mechanism.
    Thread the filler wire through the wire guide to the wire liner inside the gun cable.
    Close the feed gear and secure it with the pressure control arm. Make sure that the filler wire
    runs in the feed roll groove.
    9. Adjust the filler wire compression with the pressure control arm, no higher than to
    the middle of the scale. If the pressure is too high, the feed rolls may remove metal
    fragments from the wire surface. On the other hand, if the pressure is too low, the feed
    gear slips and the wire does not feed and run smoothly.
    10. Switch on the welding machine.
    11. Press the welding gun trigger and wait for the filler wire to exit the welding gun.
    12. Close the wire cabinet door.
    NOTE! When feeding the welding wire into the gun, be sure that you are not pointing the gun at
    anyone and that there isn’t anything in front of the gun. Also, do not put your fingers near the feed
    rolls, because they might get trapped

    2.7.3 Reversing polarity
    Some filler wires are recommended to be welded with the gun in the –pole, so the polarity
    should be reversed. Check the recommended polarity from the filler wire package.

    1.
    2.
    3.
    4.
    5.
    6.

    10

    Disconnect the machine from the mains.
    Expose the terminal connections by bending the protective rubber covers away from the
    terminal.
    Remove the terminal tightening nuts and washers. Note the correct order of the washers!
    Interchange the cables.
    Install the washers in place and re-tightening the securing nuts.
    Replace the rubber terminal covers. The rubber covers must always protect the terminals
    during use.

    MinarcMig Evo 170, Evo 200



  • Page 13

    2.8 Controls and indicator lights
    MinarcMig Evo 170 control panel
    4.

    5.

    6.

    3.

    EN
    2.

    U

    1.
    2.
    3.
    4.
    5.
    6.

    W006095

    1.

    Wire feed speed control
    Welding voltage control
    Dynamics selection control
    Standby indicator light
    Overheating indicator light
    Display

    Wire feed speed and welding voltage values are set and adjusted independently. Guide
    parameter values can be viewed on page 15 of this manual.
    The Dynamics selection control offers a choice of two settings and controls the rate of rise
    of current during the welding process, when the filler wire is in contact with the weld piece.
    Use Dynamics setting 'I' for lower welding parameter settings and small filler wires, and 'II' for
    higher parameter settings and larger filler wires.
    Indicator lights display the machine’s standby mode and inform of a possible welding duty
    cycle temperature limit. When you switch the machine on, a green standby light switches on.
    Simultaneously, the main switch indicator light switches on. If the machine reaches its duty
    cycle limit during welding or the supply voltage is too low or too high, the welding operation
    automatically switches off and the yellow overheating indicator light switches on. The light
    switches off when the machine has cooled and is ready for operation again. Make sure that
    there is enough space around the machine to allow fresh air to freely circulate and cool the
    machine.
    NOTE! Always start and stop the machine from the main switch, never use the plug as a switch!

    © Kemppi Oy / 1340

    11



  • Page 14

    MinarcMig Evo 200 control panel
    3.

    4.

    5.
    7.
    6.

    EN

    1.

    2.

    S

    U

    Machine's control panel in automatic mode
    1. Welding power control (automatic mode) OR Wire feed speed control (manual mode)
    2. Arc length trimmer (automatic mode) OR Welding voltage control (manual mode)
    3. Standby indicator light
    4. Overheating indicator light
    5. Mode selection button
    6. Material selection button (automatic mode)
    7. Display
    In automatic mode, the welding power is adjusted according to the thickness of the material
    to be welded. The machine also has a trimmer for arc length in automatic mode, which also
    influences the weld seam surface shape. There are four material options for filler wires in
    automatic mode, and you can browse through them with the material selection button. In
    manual mode, the wire feed speed and welding voltage are adjusted separately. Operation
    mode can be changed with the mode selection button. Note that material or sheet thickness
    selections made in the automatic mode are not valid in manual mode. Indicator lights display
    the machine’s standby mode and inform of a possible welding duty cycle temperature limit.
    When you switch the machine on, a green standby light switches on. Simultaneously, the main
    switch indicator light switches on. If the machine reaches its duty cycle limit during welding
    or the supply voltage is too low or too high, the welding operation automatically switches
    off and the yellow overheating indicator light switches on. The light switches off when the
    machine has cooled and is ready for operation again. Make sure that there is enough space
    around the machine to allow fresh air to freely circulate and cool the machine.
    NOTE! Always start and stop the machine from the main switch, never use the plug as a switch!

    12

    MinarcMig Evo 170, Evo 200



  • Page 15

    2.8.1 Display in automatic mode
    3.
    4.
    1.
    5.
    6.

    2.

    7.

    Machine display in automatic mode
    1. Material thickness
    2. Visual material thickness and weld shape indicator
    3. Operating mode reference
    4. Material selection
    5. Shielding gas and wire diameter recommendation
    6. Wire feed graphic
    7. Welding values: Wire feed speed, welding voltage and welding current
    MinarcMig Evo 200 automatically sets the machine based on your input selections for plate
    thickness in mm, weld shape and material type. The material thickness graphic display shows
    the selected plate thickness to be welded. Your machine is automatically set for welding
    following these parameters inputs.
    As you make your selections you will see the displayed parameters change. For example,
    as you adjust the power/plate thickness control, you will see the graphic indicating plate
    thickness become thicker or thinner.
    The selected operating mode and material type are also shown on the display. The display
    also shows a recommendation for shielding gas and filler wire diameter for the material in
    question. During welding, the graphical display shows that wire feeding is active including
    the wire feed rate. Of all the welding parameters, only filler wire feed speed is visible on the
    display all the time. Welding voltage and welding current are only visible on the display during
    welding. The last used values remain on the display until welding is restarted or parameter
    settings are changed.
    When adjusting the arc length, weld shape, or voltage control, the voltage display shows
    a comparative scale (-9…0…9) which will disappear from the display after a preset time
    following adjustment.

    EN

    2.8.2 Welding power adjustment in automatic mode
    Adjusting the welding power according to sheet thickness affects simultaneously both wire
    feed speed and amount of current delivered to the filler wire. This is a good starting point
    for welding in different operating situations. However, welding joint type and root opening
    may influence the amount of welding power required. Select the correct welding power
    using the power control, whilst viewing the graphical display of the fillet weld and sheet
    thickness indicator. If the fillet weld’s sheets are of different thickness, use their average as a
    default parameter and test weld. The sheet thickness display is given in millimetres and with
    steel and stainless steel wires, is based on 0.8 mm filler wire diameter. When using a 0.6 mm
    filler wire, set the welding power control slightly higher than the used sheet thickness and
    correspondingly slightly lower with 0.9–1.0 mm wires. With aluminium wires, the welding
    power adjustment is based on 1.0 mm wire diameter.

    © Kemppi Oy / 1340

    13



  • Page 16

    2.8.3 Arc length trimmer in automatic mode
    The arc length/weld shape/voltage trimmer adjusts the length of the arc, either shorter or
    longer, and affects the welding temperature. A shorter arc is colder and a longer one hotter.
    The arc length trimmer also affects the arc’s welding properties and influences weld spatter
    with different combinations of filler wire diameters and shielding gases. The trimmer range is
    -9...0...9: negative values shorten and positive values lengthen the arc. The trimmer is preset at
    0 which is, in most cases, a suitable basic setting.
    If the weld is too convex, the arc is too short or cold. Then adjust the arc longer or hotter by
    turning the control clockwise.
    If, on the other hand, you want to weld with a colder arc to prevent for example the parent
    material from burning through, adjust the arc shorter by turning the control counter
    clockwise. You can also adjust the welding power, if needed.
    When adjusting the arc length, the cross sectional weld joint graphic on the machines display
    changes correspondingly to either a more concave, flat or convex weld result.
    NOTE! When welding for the first time, we recommend that you set the arc length trimmer to 0.

    2.8.4 Display in manual mode

    EN

    1.

    2.

    3.

    1. Operating mode
    2. Wire feed graphic
    3. Welding values: wire feed speed, welding voltage and welding current
    The selected 'Manual' operating mode is confirmed on the display. During welding, the wire
    feed speed graphic displays the wire’s speed. Wire feed speed is the only welding parameter
    always visible on the display. When adjusting welding voltage, the display shows the set value
    for the voltage, and only during welding does the display show the actual value. Welding
    current is visible on the display only during welding. Values for actual welding voltage and
    welding current remain on the display after welding, until welding is restarted or settings are
    changed.

    14

    MinarcMig Evo 170, Evo 200



  • Page 17

    Arc dynamics

    In Manual mode you can select from two different arc dynamics settings. Press Manual mode
    button (Arc Dynamics control on MinarcMig 170 model) once to pre-select either arc dynamic
    value I or value II. Changing between setting I and setting II will adjust the short circuit
    characteristics to suit different welding applications.

    2.8.5 Adjustments in manual mode

    EN

    In manual mode, the wire feed speed and welding voltage are both adjusted separately.
    Welding current and power are defined according to wire feed speed. The desired arc and
    welding properties can be reached by adjusting the voltage.

    2.9 MIG/MAG welding
    NOTE! Welding fumes may be dangerous to your health. Ensure that there is ample ventilation
    during welding! Never look at the arc without a face shield specifically designed for arc welding!
    Protect yourself and your surrounding area from the arc and hot welding spatter!
    NOTE! Always wear protective clothing, gloves, face and eye shields suitable for welding. It is
    recommended that you make practice welds before you commence welding your main work piece.
    NOTE! The work piece will be very hot. Protect yourself and others at all times.

    You can start welding after you have made the necessary preparation described throughout
    these instructions.
    Providing you ensure that the MinarcMig Evo equipment is correctly prepared and set for
    the material type and joint to be welded, you will achieve exceptionally high quality welding
    results.
    • Ensure that the correct filler wire type and size is selected for the work piece.
    • Ensure that the correct wire liner and contact tip size is fitted to the welding gun.
    • Ensure that the correct shielding gas type is connected and the flow rate adjusted before
    welding starts.
    • Ensure the earth return clamp is connected to the work piece
    • Ensure that you are wearing the correct safety equipment before you start welding
    - including: suitable welding clothing, the correct welding face shield with a suitable
    shade welding lens, welding gloves and when necessary, a welding mask.
    NOTE! Please read section 1.2.2 before proceeding further.

    © Kemppi Oy / 1340

    15



  • Page 18

    EN
    Having checked that the MinarcMig Evo is prepared in the correct way for the welding task
    ahead, and that you are wearing the necessary protective equipment, you are ready to
    commence welding.
    MIG/MAG welding can be performed down hand, vertically and overhead: either right to left
    (Right handed operators) or left to right (left handed operators)
    First, present the welding gun nozzle to a practice work piece. The gun nozzle should be
    approximately 15 mm away from the surface of the work piece and weld joint. If welding a T
    fillet joint, the gun should be held at an angle of approximately 45 degrees, bisecting the 90
    degree joint at the midway point. Starting at the right hand side of the joint (Right handed
    operators only), lean the gun backwards slightly, so the gun nozzle is pointing forwards,
    towards the centre of the work piece. This is called a 'pushing technique' and is suitable for
    most applications.
    Pull the welding gun trigger. The filler wire will move forward, and a short circuit will occur
    and the arc will be established. Keeping the gun trigger depressed, the molten weld pool will
    start to form. Begin to travel the gun forwards, in a controlled manner and travel speed. Not
    too fast and not too slow. Providing you have correctly set your MinarcMig Evo, your welding
    power should be correctly set for the material thickness and type, and the quality of your weld
    deposit is now determined by your skill and technique.
    The resulting weld deposit, width and shape, should be consistent in appearance and quality.
    If you are welding too fast the weld bead may be too thin or even intermittent in appearance.
    Try to slow your travel speed slightly and maintain an even approach to the joint. If you are
    welding too slowly, you may find the weld deposit is too heavy, the weld piece overheats and
    possibly burns a hole through the plate. All that may be required to ensure a successful result
    here is an increase in forward travel speed, but you may also need to reduce the power setting
    slightly, to achieve the desired result.
    As with all craft skills – practice will make perfect! For more info www.kemppi.com > Welding
    ABC.

    16

    MinarcMig Evo 170, Evo 200



  • Page 19

    2.10 Using the shoulder strap
    1.

    2.

    3.

    4.

    EN
    Using and fixing the shoulder strap
    The machine is delivered with a fabric shoulder strap and metal clip set. The shoulder strap
    can be used as a convenient and comfortable way to transport both the machine and cables
    set. There are two identical metal clips. Fix one clip to each of the metal lifting eyes, located at
    the top of the machine. Adjust the shoulder strap to a comfortable length. The machine can
    now be carried.
    Should you also wish to transport and secure the cables set, place the cable bundle over the
    strap as shown, bring the strap and remaining free clip over the top of the cable bundle and
    secure to the already fastened clip. As you take the weight of the machine with the strap, the
    cable set is clamped securely into position ready for transport.
    NOTE! The machine should not be used when hanging from the shoulder strap.

    3.

    MAINTENANCE
    NOTE! Be careful when handling electrical cables!

    In maintaining the unit, take into consideration the rate of use and the environment it is
    used in. When the unit is used properly and serviced regularly, you will avoid unnecessary
    disturbances in use and production.

    3.1 Daily maintenance
    • Remove welding spatters from the welding gun’s tip and check the condition of the
    parts. Change damaged parts to new ones immediately. Only use original Kemppi spare
    parts.
    • Change damaged insulation parts to new ones immediately.
    • Check the tightness of the welding gun’s and earthing cable’s connections.
    • Check the condition of the supply voltage and welding cable and replace faulty cables.
    • Check condition of mains and welding cables and replace damaged cables.
    • See that there is enough space around the unit for ventilation.

    © Kemppi Oy / 1340

    17



  • Page 20

    3.2 Maintenance of the wire feed mechanism
    Parts of the welding gun and wire liner

    9

    EN

    1
    2
    3
    4
    5
    6
    7
    8
    9
    10
    11

    9580101
    9591010
    9876634
    9876635
    9876633
    9876636
    9580173
    9591079
    4153040
    4307650
    4307660

    8

    7

    3
    4
    5
    6

    2

    1

    0.6 mm
    0.8 mm
    0.9 mm
    1.0 mm

    45°

    10, 11

    0.6–1.0 mm (Fe, CuSi)
    0.6–1.0 mm (Ss, Al)

    Service the wire feed mechanism at least every time the spool is changed.
    • Check the wear of the feed roll groove and change the feed roll when necessary.
    • Carefully clean the welding gun wire liner with dry compressed air.
    NOTE! When using compressed air pistols, ensure you are wearing adequate safety equipment
    including, suitable work clothing, gloves and eye protection. Never direct compressed air pistols or
    the end of the liner at your skin, face or others in the vicinity.

    Cleaning the wire liner
    Pressure of the feed rolls remove metal dust from the filler wire’s surface which then travels
    in the wire liner inside the gun cable. If the wire liner is not cleaned, it gradually clogs up,
    increasing drag, impairing wire feed performance and weld quality. Ultimately this will cause
    wire feed malfunctions. Clean the liner in the following manner:
    1. Remove the welding gun’s gas nozzle, contact tip and contact tip adapter.
    2. With a pneumatic pistol, blow dry and filtered compressed air through the wire liner.
    3. Clean the wire feed mechanism and spool housing with compressed air.
    4. Reassemble the welding gun. Firmly tighten the contact tip and contact tip’s adapter.
    Replacing the wire liner
    If the wire liner is too worn or totally clogged, replace it with a new one according to the
    following instructions. You should also replace wire liner with a plastic one, if you mainly use
    stainless steel or aluminium wire.
    1. Disconnect the welding gun cable from the machine as follows.
    a. Disconnect the gun's power cable fixing clamp by opening the screws.
    b. Disconnect the gun's power cable from the machine’s pole.
    c. Disconnect the connector of the trigger conductors from the machine.
    d. Open the gun’s mounting nut.
    e. Extract the gun gently from the machine whereupon all parts come through the
    cable hole.
    2. Open the mounting nut of the wire liner, which exposes the end of the wire liner.
    3. Straighten the welding gun cable and withdraw the wire liner from the gun cable.
    4. Push a new wire liner into the gun. Make sure that the liner enters all the way into the contact
    tip’s adapter and that there is an O-ring at the machine end of the guide.

    18

    MinarcMig Evo 170, Evo 200



  • Page 21

    5.
    6.
    7.

    Tighten the wire guide in place with the mounting nut.
    Cut the wire guide 2 mm from the mounting nut and file the sharp edges of the cut round.
    Reattach the gun in place and tighten the parts to spanner tightness.

    3.3 Troubleshooting
    Problem cause
    The wire does not
    move or wire feed
    entangles

    Feed rolls, wire liner or contact tips are defective
    • Check wire mechanism adjustment is not too tight or too loose
    • Check that the feed roll groove is not too worn
    • Check that the wire liner is not blocked
    • Check that the contact tip and wire liner are suitable for the wire size used
    • Check that spatter is not blocking the contact tip and that the hole is not closed or damaged

    The main switch
    indicator will not
    light up

    • The machine has no supply voltage light
    • No electricity connected to the machine
    • Check the mains supply fuses
    • Check the mains cable and plug

    Poor welding results

    Several factors affect the welding quality
    • Check that the wire feed is constant
    • Check the trimming settings of welding power control and arc length
    • Check the material selection setting
    • Check that the earth return clamp is fixed properly, fixing point is clean, and both cable and its
    connections are undamaged
    • Check that the shielding gas is suitable for the wire material used
    • Check the flow of shielding gas from the tip of the welding gun
    • Supply voltage is uneven, too low or too high

    EN

    Overheating indicator The machine has overheated
    is illuminated
    Normally, this indicates that the device has reached its maximum designed operating temperature.
    The thermostat has become active, switching the welding power off. Allow the unit to cool and the
    machine will soon automatically reset and allow welding to restart.
    • Ensure that cooling air has unrestricted flow.
    • If the machine’s duty cycle has been exceeded, wait for indicator to turn off.
    In certain circumstances, this light may also indicate irregularity in the supply voltage.
    Too low or high supply voltage.
    If the machine’s malfunction is not eliminated with the above measures, contact Kemppi
    service.

    3.4 Storage
    Store the unit in a clean and dry place. Shield it from rain, and in temperatures exceeding
    +25 °C from direct exposure to sun.

    3.5 Disposal of the machine
    Do not dispose of electrical equipment with normal waste!
    In observance of European Directive 2002/96/EC on waste electrical and electronic
    equipment, and its implementation in accordance with national law, electrical equipment
    that has reached the end of its life must be collected separately and taken to an appropriate
    environmentally responsible recycling facility.
    The owner of the equipment is obliged to deliver a decommissioned unit to a regional
    collection centre, per the instructions of local authorities or a Kemppi representative. By
    applying this European Directive you will improve the environment and human health.

    © Kemppi Oy / 1340

    19



  • Page 22

    4.

    ORDERING NUMBERS
    includes gun, cables, gas hose and shoulder strap
    MinarcMig Evo 170
    includes gun, cables, gas hose and shoulder strap
    MinarcMig Evo 170 AU
    includes gun, cables, gas hose and shoulder strap
    MinarcMig Evo 170 (Denmark)
    includes gun, cables, gas hose and shoulder strap
    MinarcMig Evo 200
    includes gun, cables, gas hose and shoulder strap
    MinarcMig Evo 200 AU
    includes gun, cables, gas hose and shoulder strap
    MinarcMig Evo 200 (Denmark)
    3m
    Welding gun MMG22
    3m
    Earthing cable and clamp
    4.5 m
    Shielding gas hose
    Shoulder strap
    Consumables for wire feed mechanism
    0.6 – 1.0 mm
    Feed roll

    EN

    20

    0.8 – 1.0 mm, knurled

    Pressure roll
    Wire rear guide
    Parts for wire spool hub
    Spool flange
    Spring
    Wire spool lock
    Consumables for MMG22 gun
    Gas nozzle
    Gas nozzle insulating bush
    Contact tip M6
    Contact tip M6
    Contact tip M6
    Contact tip M6
    Contact tip adapter
    Neck insulating ring
    Wire guide
    Wire guide

    MinarcMig Evo 170, Evo 200

    61008170
    61008170AU
    61008170DK
    61008200
    61008200AU
    61008200DK
    6250220
    6184003
    W001077
    9592163
    W000749
    W001692
    9510112
    W000651
    W000728
    W000980
    W000727
    9580101
    9591010

    0.6 mm

    9876634

    0.8 mm

    9876635

    0.9 mm

    9876633

    1.0 mm

    9876636
    9580173
    9591079

    0.6 – 1.0 mm (Fe)

    4307650

    0.6 – 1.0 mm (Ss, Al)

    4307660



  • Page 23

    5.

    TECHNICAL DATA
    MinarcMig Evo 170
    Connection voltage
    Connection voltage (AU)
    Rated power at max. current
    Supply current
    Connection cable
    Fuse
    Output 40 °C
    Welding range
    No-load voltage
    Idle power
    Voltage steps
    Power factor at 100 % ED
    Efficiency at 100 % ED
    Filler wires ø
    Wire feed speed adjustment range
    Wire spool
    Shielding gases
    External dimensions
    Weight
    Temperature class
    EMC class
    Degree of protection
    Operating temperature range
    Storage temperature range
    Standards
    IEC 60974-1
    IEC 60974-5
    IEC 60974-10
    IEC 61000-3-12

    © Kemppi Oy / 1340

    1 ~ 50/60 Hz

    230 V ± 15 %

    1 ~ 50/60 Hz

    240 V ± 15 %

    35 % ED

    170 A/4.8 kVA

    35 % ED I1max

    20,3 A

    100 % ED I1eff

    10,1 A

    H07RN-F

    3G1.5(1.5 mm2, 3 m)

    type C

    16 A

    35% ED

    170 A/24 V

    100% ED

    100 A/20 V
    20 A/15 V – 170 A/24 V
    70 – 75 V
    12 W fan off, 21 W fan on
    0.1 V

    EN

    0.99
    80 %
    Fe solid wire

    0.6…1.0 mm

    Fe cored wire

    0.8…1.0 mm
    1…12 m/min

    max. ø

    200 mm/5 kg
    CO₂, Ar + CO₂-mixed

    LxWxH

    450 x 227 x 368 mm

    incl. gun and cables 3.0 kg

    13 kg
    F (155 °C)
    A
    IP23S
    -20…+40 °C
    -40…+60 °C

    21



  • Page 24

    MinarcMig Evo 200
    Connection voltage
    Connection voltage (AU)
    Rated power at max. current
    Supply current
    Connection cable
    Fuse
    Output 40 °C

    EN

    Welding range
    No-load voltage
    Idle power
    Voltage steps
    Power factor at 100 % ED
    Efficiency at 100 % ED
    Filler wires ø

    Wire feed speed adjustment range
    Wire spool
    Shielding gases
    External dimensions
    Weight
    Temperature class
    EMC class
    Degree of protection
    Operating temperature range
    Storage temperature range
    Standards
    IEC 60974-1
    IEC 60974-5
    IEC 60974-10
    IEC 61000-3-12

    22

    MinarcMig Evo 170, Evo 200

    1 ~ 50/60 Hz

    230 V ± 15 %

    1 ~ 50/60 Hz

    240 V ± 15 %

    35 % ED

    200 A/6.2 kVA

    35 % ED I1max

    26.2 A

    100 % ED I1eff

    13.2 A

    H07RN-F

    3G1.5(1.5 mm2, 3 m)

    type C

    16 A

    35% ED

    200 A/24 V

    100% ED

    120 A/20 V
    20 A/15 V – 200 A/26 V
    70 – 75 V
    12 W fan off, 26 W fan on
    0.1 V
    0.99
    82 %

    Fe solid wire

    0.6…1.0 mm

    Fe cored wire

    0.8…1.0 mm

    Ss

    0.8…1.0 mm

    Al

    1.0 mm

    CuSi

    0.8…1.0 mm
    1…13 m/min

    max. ø

    200 mm/5 kg
    CO₂, Ar, Ar + CO₂-mixed

    LxWxH

    450 x 227 x 368 mm

    incl. gun and cables 3.0 kg

    13 kg
    F (155 °C)
    A
    IP23S
    -20…+40 °C
    -40…+60 °C



  • Page 25



  • Page 26

    KEMPPI OY
    Kempinkatu 1
    PL 13
    FIN-15801 LAHTI
    FINLAND
    Tel +358 3 899 11
    Telefax +358 3 899 428
    export@kemppi.com
    www.kemppi.com

    KEMPPI (UK) Ltd
    Martti Kemppi Building
    Fraser Road
    Priory Business Park
    BEDFORD, MK44 3WH
    UNITED KINGDOM
    Tel +44 (0)845 6444201
    Telefax +44 (0)845 6444202
    sales.uk@kemppi.com

    Kotimaan myynti:
    Tel +358 3 899 11
    Telefax +358 3 734 8398
    myynti.fi@kemppi.com

    KEMPPI FRANCE S.A.S.
    65 Avenue de la Couronne des Prés
    78681 EPONE CEDEX
    FRANCE
    Tel +33 1 30 90 04 40
    Telefax +33 1 30 90 04 45
    sales.fr@kemppi.com

    KEMPPI SVERIGE AB
    Box 717
    S-194 27 UPPLANDS VÄSBY
    SVERIGE
    Tel +46 8 590 783 00
    Telefax +46 8 590 823 94
    sales.se@kemppi.com
    KEMPPI NORGE A/S
    Postboks 2151, Postterminalen
    N-3103 TØNSBERG
    NORGE
    Tel +47 33 346000
    Telefax +47 33 346010
    sales.no@kemppi.com
    KEMPPI DANMARK A/S
    Literbuen 11
    DK-2740 SKOVLUNDE
    DANMARK
    Tel +45 4494 1677
    Telefax +45 4494 1536
    sales.dk@kemppi.com
    KEMPPI BENELUX B.V.
    Postbus 5603
    NL-4801 EA BREDA
    NEDERLAND
    Tel +31 765717750
    Telefax +31 765716345
    sales.nl@kemppi.com

    KEMPPI GmbH
    Perchstetten 10
    D-35428 LANGGÖNS
    DEUTSCHLAND
    Tel +49 6 403 7792 0
    Telefax +49 6 403 779 79 74
    sales.de@kemppi.com

    OOO KEMPPI
    Polkovaya str. 1, Building 6
    127018 MOSCOW
    RUSSIA
    Tel +7 495 739 4304
    Telefax +7 495 739 4305
    info.ru@kemppi.com
    ООО КЕМППИ
    ул. Полковая 1, строение 6
    127018 Москва
    Tel +7 495 739 4304
    Telefax +7 495 739 4305
    info.ru@kemppi.com
    KEMPPI, TRADING (BEIJING) COMPANY,
    LIMITED
    Room 420, 3 Zone, Building B,
    No.12 Hongda North Street,
    Beijing Economic Development Zone,
    100176 Beijing
    CHINA
    Tel +86-10-6787 6064
    +86-10-6787 1282
    Telefax +86-10-6787 5259
    sales.cn@kemppi.com

    KEMPPI SPÓŁKA Z O.O.
    Ul. Borzymowska 32
    03-565 WARSZAWA
    POLAND
    Tel +48 22 7816162
    Telefax +48 22 7816505
    info.pl@kemppi.com

    肯倍贸易(北京)有限公司
    中国北京经济技术开发区宏达北路12号
    创新大厦B座三区420室 (100176)
    电话: +86-10-6787 6064
    +86-10-6787 1282
    传真: +86-10-6787 5259
    sales.cn@kemppi.com

    KEMPPI AUSTRALIA PTY LTD.
    13 Cullen Place
    P.O. Box 5256, Greystanes NSW 2145
    SMITHFIELD NSW 2164
    AUSTRALIA
    Tel. +61 2 9605 9500
    Telefax +61 2 9605 5999
    info.au@kemppi.com

    KEMPPI INDIA PVT LTD
    LAKSHMI TOWERS
    New No. 2/770,
    First Main Road,
    Kazura Garden,
    Neelankarai,
    CHENNAI - 600 041
    TAMIL NADU
    Tel +91-44-4567 1200
    Telefax +91-44-4567 1234
    sales.india@kemppi.com
    1910020
    1340

    www.kemppi.com






Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kemppi MinarcMig Evo 170 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Holen Sie sich Ihr Benutzerhandbuch per E-Mail

Geben Sie Ihre E-Mail-Adresse ein, um das Handbuch zu erhalten von Kemppi MinarcMig Evo 170 in der Sprache / Sprachen: Englisch als Anhang in Ihrer E-Mail.

Das Handbuch ist 3,18 mb groß.

 

Sie erhalten das Handbuch in Ihrer E-Mail innerhalb von Minuten. Wenn Sie keine E-Mail erhalten haben, haben Sie wahrscheinlich die falsche E-Mail-Adresse eingegeben oder Ihre Mailbox ist zu voll. Darüber hinaus kann es sein, dass Ihr ISP eine maximale Größe für E-Mails empfangen kann.

Andere Handbücher von Kemppi MinarcMig Evo 170

Kemppi MinarcMig Evo 170 Bedienungsanleitung - Holländisch - 26 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info