686270
17
Zoom out
Zoom in
Vorherige Seite
1/26
Nächste Seite
EN
Arc dynamics
In Manual mode you can select from two dierent arc dynamics settings. Press Manual mode
button (Arc Dynamics control on MinarcMig 170 model) once to pre-select either arc dynamic
value I or value II. Changing between setting I and setting II will adjust the short circuit
characteristics to suit dierent welding applications.
2.8.5 Adjustments in manual mode
In manual mode, the wire feed speed and welding voltage are both adjusted separately.
Welding current and power are dened according to wire feed speed. The desired arc and
welding properties can be reached by adjusting the voltage.
2.9 MIG/MAG welding
NOTE! Welding fumes may be dangerous to your health. Ensure that there is ample ventilation
during welding! Never look at the arc without a face shield specically designed for arc welding!
Protect yourself and your surrounding area from the arc and hot welding spatter!
NOTE! Always wear protective clothing, gloves, face and eye shields suitable for welding. It is
recommended that you make practice welds before you commence welding your main work piece.
NOTE! The work piece will be very hot. Protect yourself and others at all times.
You can start welding after you have made the necessary preparation described throughout
these instructions.
Providing you ensure that the MinarcMig Evo equipment is correctly prepared and set for
the material type and joint to be welded, you will achieve exceptionally high quality welding
results.
• Ensure that the correct ller wire type and size is selected for the work piece.
• Ensure that the correct wire liner and contact tip size is tted to the welding gun.
• Ensure that the correct shielding gas type is connected and the ow rate adjusted before
welding starts.
• Ensure the earth return clamp is connected to the work piece
• Ensure that you are wearing the correct safety equipment before you start welding
- including: suitable welding clothing, the correct welding face shield with a suitable
shade welding lens, welding gloves and when necessary, a welding mask.
NOTE! Please read section 1.2.2 before proceeding further.
15
© Kemppi Oy / 1340
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kemppi MinarcMig Evo 170 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Kemppi MinarcMig Evo 170

Kemppi MinarcMig Evo 170 Bedienungsanleitung - Holländisch - 26 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info