686270
20
Zoom out
Zoom in
Vorherige Seite
1/26
Nächste Seite
EN
3.2 Maintenance of the wire feed mechanism
Parts of the welding gun and wire liner
12789 3
4
5
6
1 9580101
10, 11
2 9591010
3 9876634
0.6 mm
4 9876635
0.8 mm
5 9876633
0.9 mm
6 9876636
1.0 mm
7 9580173
8 9591079
9 4153040
45°
10 4307650
0.6–1.0 mm (Fe, CuSi)
11 4307660
0.6–1.0 mm (Ss, Al)
Service the wire feed mechanism at least every time the spool is changed.
• Check the wear of the feed roll groove and change the feed roll when necessary.
• Carefully clean the welding gun wire liner with dry compressed air.
NOTE! When using compressed air pistols, ensure you are wearing adequate safety equipment
including, suitable work clothing, gloves and eye protection. Never direct compressed air pistols or
the end of the liner at your skin, face or others in the vicinity.
Cleaning the wire liner
Pressure of the feed rolls remove metal dust from the ller wires surface which then travels
in the wire liner inside the gun cable. If the wire liner is not cleaned, it gradually clogs up,
increasing drag, impairing wire feed performance and weld quality. Ultimately this will cause
wire feed malfunctions. Clean the liner in the following manner:
1. Remove the welding guns gas nozzle, contact tip and contact tip adapter.
2. With a pneumatic pistol, blow dry and ltered compressed air through the wire liner.
3. Clean the wire feed mechanism and spool housing with compressed air.
4. Reassemble the welding gun. Firmly tighten the contact tip and contact tips adapter.
Replacing the wire liner
If the wire liner is too worn or totally clogged, replace it with a new one according to the
following instructions. You should also replace wire liner with a plastic one, if you mainly use
stainless steel or aluminium wire.
1. Disconnect the welding gun cable from the machine as follows.
a. Disconnect the gun's power cable xing clamp by opening the screws.
b. Disconnect the gun's power cable from the machines pole.
c. Disconnect the connector of the trigger conductors from the machine.
d. Open the guns mounting nut.
e. Extract the gun gently from the machine whereupon all parts come through the
cable hole.
2. Open the mounting nut of the wire liner, which exposes the end of the wire liner.
3. Straighten the welding gun cable and withdraw the wire liner from the gun cable.
4. Push a new wire liner into the gun. Make sure that the liner enters all the way into the contact
tips adapter and that there is an O-ring at the machine end of the guide.
MinarcMig Evo 170, Evo 200
18
20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kemppi MinarcMig Evo 170 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Kemppi MinarcMig Evo 170

Kemppi MinarcMig Evo 170 Bedienungsanleitung - Holländisch - 26 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info