686375
25
Zoom out
Zoom in
Vorherige Seite
1/27
Nächste Seite
25
Robot Gun Cleaning Station© Kemppi Oy 2016 1616
OPERATING MANUAL
14. TROUBLESHOOTING
If the measures described below are not successful, please consult your dealer or the manufacturer.
Also consult the operating instructions for the welding components: the welding power source, welding torch system,
re-circulating cooling unit, and so on.
Problem Cause Solution
Compressed-air motor does not run Compressed-air supply or hose connection interrupted
Compressed-air supply or hose connection interrupted
Check all supply lines leading to the cylinder and the ttings
Motor defective; replace
Replace directional valve Y2
Insucient cleaning Milling cutter defective or worn out Replace milling cutter
Welding torch parts damaged Wrong equipment parts Check torch-dependent parts (milling cutter and clamping prism)
Check immersion depth of torch
Table 12: Troubleshooting the injection unit
Problem Cause Solution
No injection Insucient uid level
Compressed-air supply or hose connections
interrupted
Directional valve Y4 does not switch
Add more anti-spatter uid
Check all supply lines leading to the cylinder and the ttings
Replace directional valve Y4
Too much or too little spray mist Metering quantity incorrectly adjusted Change setting of throttle screw
Too little spray mist Injection time too short
Operating pressure too low
Injection time greater than waiting time
Check operating pressure
No spray mist Operating pressure too low Check operating pressure
Table 13: Troubleshooting the wire-cutting device
Problem Cause Solution
No cutting function Compressed-air supply or hose connection interrupted
Directional valve Y3 does not switch
Check all supply lines leading to the cylinder and the ttings
Check signal output of robot control
Replace directional valve Y3
Insucient cutting capacity Too low working pressure
Roughly running slide
Worn cutting edge
Check the adjustment of the pressure regulator: min. 5 bar, max. 8 bar
Unmount movable parts; clean and lubricate them
Clean more often
Change approach position P4
Change the cutter
Free wire end is bent The wire has no contact with the xed jaws
Counter-support jammed
Correct the approach position of the welding torch
Unmount movable parts; clean and oil them
Tighten the mounting screws
25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kemppi Robot Gun Cleaning Station wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info