159527
80
Zoom out
Zoom in
Vorherige Seite
1/84
Nächste Seite
80
Knowledge sections
Important Items
In case of difficulty
What seems to be a malfunction is not always so. Before calling for service, check the following table
according to the symptom of your trouble.
Operation to reset
The microcomputer may fall into malfunction (impossibil-
ity to operate, erroneous display, etc.) when the power
cord is unplugged while unit is ON or due to an external
factor. In this case, execute the following procedure to
reset the microcomputer and return it to normal condi-
tion.
Unplug the power cord from the power outlet then,
while holding the
key depressed, plug the
power cord again.
÷ Please note that resetting the microcomputer clears
the contents stored in and it returns to condition
when it left the factory.
Sound is not produced.
The "standby/timer" indicator blinks in red
and no sound is put out.
The "standby/timer" indicator blinks in amber.
No sound from the headphones.
Sound is not produced from the left or right
speakers.
The clock display blinks without changing the
figures.
Timer operation is not possible.
÷ Connect properly referring to "System connections". 6
÷ Adjust to an required volume.
÷ Switch MUTE OFF.
%
÷ Unplug the headphone plug.
÷ A speaker cord is short-circuited. Turn power off and re-connect
the speaker cord.
÷ Adjust the present time again.
÷ Insert correctly. %
÷ Adjust to an required volume. $
÷ Connect properly referring to "System connections". 6
÷ Adjust the present time again.
÷ Adjust the present time referring to "Clock adjustment".
÷ Set the timer ON time and OFF time. g
÷ Press the TIMER key to set up the execution. dh
÷ Connect antennas. 7
÷ Select a band. ¢
÷ Tune to the frequency of the desired station. ¢
÷ Install the outdoor antenna in an apart position from the road.
÷ Switch the suspected electric appliance OFF.
÷ Install the TV or the system at an increased distance between
them.
÷ Preset stations with tunable frequencies.
÷ Preset stations again.
Radio stations cannot be received.
Noise interferes.
A station has been preset but it cannot be
received by pressing the P.CALL key.
RemedySymptom
RemedySymptom
Amplifier section/Speakers
Tuner section
80

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kenwood hm 383 md wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info