477378
33
Zoom out
Zoom in
Vorherige Seite
1/36
Nächste Seite
33
EN
ENGLISH
Amplifier
Cause
The speaker cords are disconnected.
VOLUME is set to the minimum position.
MUTE is ON.
The SPEAKERS switches are set to OFF.
Speaker cords are short-circuited.
The speaker cord is disconnected.
• The surround speaker cords and/or the center
speaker cord is disconnected.
A surround mode has not been activated.
The surround and/or center volume controls
are set to the minimum level.
The audio cord from the record player is not
connected to the PHONO jacks.
The record player is not grounded.
There are many possible causes for this
problem, depending on the type of DVD player
used.
The input mode is set to digital manual.
The software is copy-guarded.
Remedy
Connect them properly referring to “Connecting
the speakers”. $
Adjust the volume to a proper level.
Turn OFF the MUTE. )
Set the SPEAKERS switch to ON. (
Turn the power off, eliminate the short-
circuiting, then turn on the power again.
Connect it properly referring to “Connecting
the speakers”. $
Connect it properly referring to “Connecting
the speakers”. $
Select a surround mode.
Adjust the speaker levels using the test tone.
*
Insert the audio cord plugs securely into the
PHONO jacks.
Connect the grounding wire to the GND terminal
on the rear panel.
Set the input mode to digital manual before
starting playback of the Dolby Digital source.
9
Press the INPUT MODE key to select to full
auto mode. 9
Copy-guarded video software cannot be
recorded.
Symptom
No sound from the speakers.
The standby indicator blinks and sound is
not output.
Sound is not output from one of the speakers.
Sound is not output from the surround
speakers and / or the center speaker, or their
sound is very soft.
A humming noise is generated when the
PHONO input selector is selected.
When playing a Dolby Digital source signal
using a DVD player, the sound is cut off soon
after it starts.
No sound is produced during playback from
a DVD player.
A video source cannot be recorded normally.
In case of difficulty
Tuner
Cause
No antenna is connected.
The broadcast band is not set properly.
The frequency of the desired station is not
tuned.
Noise due to ignition of an automobile.
Noise due to interference from an electric
appliance.
Noise due to a nearby TV set.
• The preset station belongs to a frequency that
cannot be received.
• The preset memory was cleared because the
power cord had been unplugged for a long
period of time.
Remedy
Connect an antenna. %
Set the broadcast band properly.
Tune the frequency of the desired station.
Install the outdoor antenna away from the
road.
Turn off the power to the appliance.
Install the receiver farther away from the TV.
Preset a station with a receivable frequency.
Preset the station again.
Symptom
Radio stations cannot be received.
Interference.
A station which was preset cannot be
received by pressing the corresponding
numeric key.
Resetting the Microcomputer
The microcomputer may malfunction (unit cannot be operated,
or shows an erroneous display) if the power cord is unplugged
while the power is ON, or due to some other external factor. If
this happens, execute the following procedure to reset the
microcomputer and return the unit to its normal operating
condition.
With the power cord plugged in, turn the POWER ON/
OFF key OFF. Then, while holding down the ON/
STANDBY
key, press POWER ON/OFF key.
Please note that resetting the microcomputer will clear the contents
of the memory and return the unit to the state it was in when it
left the factory
*5339/31-36/EN 10/1/03, 8:36 PM33
33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kenwood KRF-V5070D wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Kenwood KRF-V5070D

Kenwood KRF-V5070D Bedienungsanleitung - Deutsch - 36 seiten

Kenwood KRF-V5070D Bedienungsanleitung - Französisch, Italienisch, Spanisch - 180 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info