473137
4
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
KTF-3010/KTF-2010 (En)
4
R
L
TUNER
SYSTEM CONTROL
ƒ
PHONES A SPEAKER B BASS TREBLE BALANCE
INPUT SELECTOR
MUTING LOUDNESS
ON OFF
POWER
ON/STANDBY
STEREO INTEGRATED AMPLIFIER KAF-3010R
MIN MAX
VOLUME CONTROL
MDTAPETUNERPHONOCD
SOURCE DIRECT
thermally reactive advanced instantaneous transistor TRAIT
|{ |{
LR
ANTENNA
GND
AM
FM 75
BA
SYSTEM
CONTROL
ƒ
OUTPUT
R
L
SL16 XS 8
SL16 XS 8
System connection
Connection of the Audio components/Connection of the system control cord
Make connections as shown below.
When connecting the related system components, refer also
to the instruction manuals of the related components.
Do not plug in the power lead until all connections are com-
pleted.
Pre-main amplifier
Audio cord
System control cord
To wall AC
outlet
1.Connect all cords firmly. If connections are loose, you may lose the sound or interconnectable system control operations may not work.
2.When plugging and unplugging connection cord, be sure to first remove the power cord from the AC outlet. Plugging / unplugging
connection cords without removal of the power cord can cause malfunctions or damage to the unit.
Malfunction of microcomputer
If operation is not possible or erroneous display ap-
pears even though all connections have been made
properly, rest the microcomputer referring to "In case
of difficulty". ^
Notes
Notes
KTF-3010 only
Connecting system control cords after connecting a Kenwood audio component system lets you take advantage of convenient system
control operations.
There are two Kenwood system control modes. Make connections according to the groups of terminal symbols shown below.
[SL16] Mode : for
terminals only
[XS8] Mode : lets you combine F, f, and ƒ terminals
This unit is compatible with both [SL16] and [XS8] modes. It comes from the factory set to the [SL16] mode. To switch to the [XS8] mode,
follow the instructions in “Switching from [SL16] to [XS8]”.
1. [SL16] equipment cannot be combined with [XR], [XS], and [XS8] equipment for system
operations. If your equipment consists of this kind of combination, please do not connect
any system control cords. Even without system control cords, normal operations can be
carried out without affecting performance.
2. If your amp or receiver does not have a system control terminal, do not connect any
system control cords to the system control terminals on the other components.
3. Do not connect system control cords to any components other than those specified by
Kenwood. It may cause a malfunction and damage your equipment.
4. Be sure the system control plugs are inserted all the way in to the system control termi-
nals.
Notes
Notes
Caution regarding placement
To maintain proper ventilation, be sure to leave a space around the
unit (from the largest outer dimensions including projections) equal
to, or greater than, shown below.
Left and right panels: 10 cm
Rear panel: 10 cm
No matter to which of the two terminals the con-
nection is made, the use method is the same.
The system control connection
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kenwood KTF 3010-2010 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info