Bedienungsanleitung Kenwood NXR-700 (Seite 2 von 8) (Englisch, Französisch, Spanisch)

465293

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

NXR-700 / NXR-800 INSTRUCTION MANUAL

VHF DIGITAL BASE-REPEATER / UHF DIGITAL BASE-REPEATER

THANK YOU!

We are grateful you purchased this Kenwood repeater. We

believe this easy-to-program repeater will be highly effective in

your communications system, and will keep personnel operating

at peak efﬁ ciency.

Kenwood incorporates the latest in advanced technology into

all of our products. As a result, we feel strongly that you will be

pleased with the quality and features of this product.

PRECAUTIONS

• Do not expose the unit to rain or moisture; to prevent ﬁ re or

electric shock.

• Do not open the unit under any circumstances; to avoid risk

of electric shock.

• Do not expose the unit to long periods of direct sunlight, nor

place it close to heating appliances.

• Do not place the unit in excessively dusty and/or humid

areas, nor on unstable surfaces.

• If you detect an abnormal odor or smoke coming from the

unit, disconnect the power from the unit immediately. Contact

your Kenwood service center or dealer.

NOTICES TO THE USER

◆

Government law prohibits the operation of unlicensed radio

transmitters within the territories under government control.

◆

Illegal operation is punishable by ﬁ ne and/or imprisonment.

◆

Refer service to qualiﬁ ed technicians only.

FCC WARNING

This equipment generates or uses radio frequency energy. Changes

or modiﬁ cations to this equipment may cause harmful interference

unless the modiﬁ cations are expressly approved in the instruction

manual. The user could lose the authority to operate this equipment

if an unauthorized change or modiﬁ cation is made.

INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY

THE FCC

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can generate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur

in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment to an outlet on a circuit different from that

to which the receiver is connected.

•

Consult the dealer for technical assistance.

The AMBE+2 voice coding Technology embodied in this product

is protected by intellectual property rights including patent rights,

copyrights and trade secrets of Digital Voice Systems, Inc. This voice

coding Technology is licensed solely for use within this Communications

Equipment. The user of this Technology is explicitly prohibited from

attempting to extract, remove, decompile, reverse engineer, or

disassemble the Object Code, or in any other way convert the Object

Code into a human-readable form. U.S. Patent Nos. #5,870,405,

#5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050,

#5,630,011, #5,581,656, #5,517,511, #5,491,772, #5,247,579,

#5,226,084 and #5,195,166.

◆

This repeater is intended for use as a ﬁ xed base station with

the antenna located outdoors on the rooftop or on an antenna

tower.

◆

This repeater is designed for a 13.8 V DC power source!

Never use a 24 V DC or higher source to power the repeater.

◆

Use only the supplied DC cord.

◆

Do not remove the ferrite core attached to the DC cord. Doing

so may cause interference with radio communications.

UNPACKING AND CHECKING EQUIPMENT

Note: The following unpacking information is for use by your

Kenwood dealer, an authorized Kenwood service center, or the

factory.

Carefully unpack the repeater. We recommend that you identify

the items listed in the following table before discarding the

packing material. If any items are missing or have been damaged

during shipment, ﬁ le a claim with the carrier immediately.

Item Part Number Quantity

Front glass B10-2781-XX 1

Dressed screw N08-0563-XX 1

Bracket J29-0725-XX 2

Flat head machine screw N32-4008-XX 4

Handle and screw set K01-0421-XX 1

DC cord E30-3344-XX 1

Lead wire with connector (15 pin) E37-1381-XX 1

Fuse (7.5 A) F05-7521-XX 1

Instruction Manual B62-1994-XX 1

Pamphlet B59-2457-XX 1

Pamphlet B59-2458-XX 1

Serial number sticker B42-7325-XX 1

INSTALLATION

To install the handles onto the front panel of the repeater, align

the handles with the holes on the front panel, then secure the

handles using the supplied screws.

Please consult your dealer for installing the repeater and

antenna.

MICROPHONE

Connect an optional KMC-30, KMC-35, or KMC-9C Kenwood

microphone to the MICROPHONE jack on the front panel.

OCXO UNIT (KXK-3):Option

The OCXO unit (KXK-3) is an Oven Controlled Crystal Oscillator

(OCXO) unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood NXR-700 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood NXR-700

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info