Bedienungsanleitung Kenwood TM-D710GA (Seite 77 von 77) (Englisch)

606707

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

SKY CMD-3

CONTROL OPERATION

When in the Sky Command mode, the Microphone keys of

the Commander will function as below. First switch ON the HF

transceiver and press Microphone [0] on the Commander.

Each time you press the desired key, the Commander will

automatically enter transmit mode and send the corresponding

control command to the Transporter.

Key Function

[1] (PWR) Power ON/ OFF

[2] (RX) HF frequency receive ON/ OFF

[3] (MODE) Modulation mode switch

[4] (RIT)

RIT ON/ OFF

[5] (XIT)

XIT ON/ OFF

[6] (CLR)

RIT offset or XIT offset clear

[7] (SPLIT)

Split-frequency ON/ OFF

[8] (M>V)

Transfer from Memory to VFO

[9] (A/B)

In VFO mode: VFO A/ VFO B switch

In Memory Recall mode: no change

[0] (SYNC)

Current settings retrieve (from HF transceiver)

[A] (MONI)

To monitor the UHF band on the

Commander

[B] (M/V)

VFO/ Memory Recall mode switch

[C] (UP)

XIT/ RIT offset frequency increase

[D] (DOWN)

XIT/ RIT offset frequency decrease

[ ]

(FAST)

In LSB, USB, or CW mode: 10 Hz/ 1 kHz

switch

In FM or AM mode: 1 kHz/ 10 kHz switch

[#]

(ENTER)

In VFO mode: frequency entry ON

In Memory Recall mode: channel number

entry ON

[PTT]

To transmit audio on an HF frequency

“FS” appears when you select 1 kHz step (LSB/ USB/ CW) or 10 kHz step (FM/

AM).

After pressing Mic [#], press Mic [0] to [9] to enter a frequency or memory

channel number.

Note: To change the frequency or memory channel on the HF transceiver,

rotate the Tuning control.

PROGRAMMING CALLSIGNS

The built-in TNCs of the Commander and Transporter

communicate each other when you send a control command

from the Commander. So you must program different callsigns (9

digits max.) on these transceivers as the IDs of the TNCs.

Use the following Menu Nos. to program callsigns:

On Commander

700

COMMANDER

CALLSIGN

Callsign for Commander

701

TRANSPORTER

CALLSIGN

Callsign for Transporter

On Transporter

700

COMMANDER

CALLSIGN

Callsign for Commander

701

TRANSPORTER

CALLSIGN

Callsign for Transporter

1 Access Menu 700 or 701, then press the Tuning control.

• The callsign entry ﬁ eld appears; the ﬁ rst digit blinks.

2 Rotate the Tuning control to select a character.

• You can enter 0 to 9, A to Z, and –.

3 Press [].

• The cursor moves to the next digit.

4 Repeat steps 2 and 3 to enter up to 9 digits.

[BACK]: Cancels entry of a callsign.

[]: Causes the cursor to move backward.

[INS]: Inserts the currently selected character.

[CLR]: Deletes the digit at which the cursor is blinking.

5 Press the Tuning control to complete the setting.

6 Press [ESC] to exit Menu mode.

The keypad on the Microphone also is available to enter

alphanumeric characters in step 2.

PROGRAMMING A TONE FREQUENCY

On receiving a tone from the Commander, the Transporter

causes the HF transceiver to enter Transmit mode. On both the

Commander and Transporter, access Menu 702 and select the

desired, same tone frequency.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TM-D710GA Seite 77

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TM-D710GA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info