462344
5
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
5
Training computer with digital display
Starting the device
Insert 2 batteries. (1,5 V UM 3/AA). The computer carries out
a segment test and shows all presentable signs. A beep sounds
for confirmation.
1. Start without previous knowledge
You can begin with the
training without previous
knowledge. In the
display, the different infor-
mation is shown. For an
efficient training and for
setting your personal
training specifications,
please read and follow
these operating instruc-
tions.
Read also the
general tips in the training
instructions.
After switching on the unit
starting via RESET, the complete display information will appear
= segment test with an audible signal. Afterwards, the time is
shown briefly. Time can be adjusted via the UP and DOWN
keys: First, set hours UP / DOWN, then confirm via MODE ,
then set minutes, and confirm time setting again via MODE
2. Function keys
MODE
Through shortly pressing the
MODE key, you select between the
functions [TIME, DISTANCE,
CALORIES or PULSE] both for the
display as well as for your per-
sonal settings.
If you press the MODE key for a
longer time, all values are set to
>0<.
DOWN / UP
The default values are set via the DOWN or UP keys. To this
end, the unit must be in a STOP position;
> top left symbol .
DOWN downward setting of default values.
By briefly pressing the DOWN key, you reduce the setting
values of the various functions > [TIME, DISTANCE, CALORIES
and PULSE]. If you press the DOWN key for a longer period
of time, the setting value can be reached in a faster counting
sequence.
UP upward setting of default values.
By briefly pressing the UP key, you increase the setting values
of the various functions > [TIME, DISTANCE, CALORIES and
PULSE]. If you press the UP key for a longer period of time, the
setting value can be reached in a faster counting sequence.
RESET
With the RESET key, the functions are set to >0<. With the input
settings of the respective function, only the value of these func-
P
Functions and Operation of the Training Computer
tions is set to >0< through shortly pressing the RESET key. If the
RESET key is pressed for longer than 2 seconds, all values are
set to >0<, this corresponds to a new start of the computer.
When exchanging the batteries, all values are set back to >0<
as well.
RECOVERY
Use the RECOVERY key to activate the recovery pulse function
after exercising.
3. Functions – Display
General:
In the display respectively a large display and at the same time
several segment displays appear in the lower area next to
each other.
After finishing exercising, the exercise data remains and can
be called up when you begin exercising again. The new data
is then added to these.
Exception: The computer was set to >0< with RESET, in the
personal exercise presettings the value was set at >0< or the
batteries were changed.
With an interruption of the exercising for 4 minutes, the
main screen is shut off.
If the computer shows undefinable displays, take out the bat-
teries, replace them again and try it again.
SCAN
Alternating display of all
functions in large display.
Left in the display res-
pectively the designation
appears in a shortened
form:
RPM = Round Per Minute = Rotations per minute / pedal fre-
quency
SPD = SPEED
TM = TIME = Exercise time
DST = DISTANCE = distance covered
CAL = CALORIES = Energy, calorie consumption
PLS = PULSE = Pulse frequency
If the large display with the respec-tive unit appears, the fun-
ction des-cription blinks in the small window.
RPM /SPEED
In this display, at turning intervalls (every 6
seconds), the pedaling frequency as RPM
(=rotations per minute) and the speed SPEED
in km/r are shown. The highest speed is
99.9 km/h.
TIME
In this display the exercise time is mea-
sured. The maximum time measurement
is 99:99 minutes.
DISTANCE
The distance covered is measured in km.
The counting of the distance begins with
>0< and a maximum of up to 99.9 km
can be shown. The counting grading follows in 0.01 km sec-
tions = 10 meters.
GB
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kettler Saphir 200 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info