Bedienungsanleitung Kicker zx 700 5 (Seite 5 von 28) (Deutsch, Englisch, Französisch, Spanisch)

167678

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

OPERATION

AUTO

TURN ON

+12V DC AUDIO

XOVER2

OFF HI

XOVER1

OFF HI

REMOTE

BASS

AMP1 INPUT

L+ L- R+ R-

+ SUB -

AMP2 INPUT

INPUT

LEVEL

OFF

FADER

AMP2

SUB

INPUT

LLR

SUB INPUT

Automatic Turn-On Selection: The ZX series offers three different automatic turn-on modes that can be

selected on the end panel; +12V, DC Offset, and Audio. Using either the DC Offset or Audio mode causes the

REM terminal to have +12V out for turning on additional ampliﬁ ers.

• Remote Turn-On: Set the switch to +12V to use the remote turn-on lead from your source unit. Run 18

gauge wire from the Remote Turn-On Lead on your source unit to the terminal labeled REM between the

ampliﬁ er’s positive and negative power terminals. This is the preferred automatic turn-on method.

• DC Offset Turn-On: If Remote Turn-On is not an option, the next best setting is DC Offset. The DC Offset

mode detects a 6V DC offset from the HI-Level speaker outputs when the source unit has been turned on.

• Signal Sense Turn-On: The Audio setting is the ﬁ nal alternative for Automatic turn-on. This is a Signal Sense

turn-on method that detects the incoming audio signal from your source unit and automatically turns on the

amp. This turn-on method will not work properly if the input gain control is not set appropriately.

Input Level: The RCA inputs on KICKER ZX ampliﬁ ers are capable of receiving either Hi or Low-level signals

from your source unit. If the only output available from your source unit is a Hi-Level signal, simply press in the

Input Level switch on the ampliﬁ er. Refer to the wiring section of this manual for additional instructions.

Fader Switch: Depress the fader switch if you are running two sets of inputs (front and rear for example) to the

ampliﬁ er. Leave the fader switch OFF if you want to drive all channels from a single stereo input.

Sub Input: If there is no dedicated output on your source unit for a subwoofer, use the SUB INPUT switch to set

your subwoofer input to either SUB INPUT or AMP INPUT 2.

Crossover Switch: Use the XOVER switch on the end panel of the ampliﬁ er to set the internal crossover to OFF

or HI. When the switch is set to OFF, a full bandwidth signal will be ampliﬁ ed. Set the switch to HI if you want the

ampliﬁ er’s internal crossover to serve as a high-pass ﬁ lter. Never change the crossover “OFF/HI” switch setting

with the audio system on!

Input Gain Control: The input gain control is not a volume control. It matches the output of the source unit to

the input level of the ampliﬁ er. Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it

to 25). Next, slowly turn (clockwise) the gain on the ampliﬁ er up until you can hear audible distortion, then turn it

down a little.

Bass Boost Control: The variable bass boost control on the top of the ampliﬁ er is designed to give you

increased output, 0–18dB, at 40 Hz. The setting for this control is subjective. If you turn it up, you must readjust

the input gain control to avoid clipping the ampliﬁ er.

Crossover Control: The variable crossover on the top of the ampliﬁ er allows you to adjust the crossover

frequency from 50–200Hz. The setting for this control is subjective; 80Hz is a good place to start.

Remote Bass-ZXRC (not included): When using the remote bass level control, you have the ability to control

the output level of the ampliﬁ er remotely. To mount the ZXRC remote bass level control, simply screw the metal

bracket to the chosen location, then slide the housing onto the bracket until it snaps into place. Run the cable

from the controller to the “Remote Bass” jack on the ampliﬁ er chassis.

2011 ZX 700.5 RevB.indd 52011 ZX 700.5 RevB.indd 5 10/12/2010 10:41:54 AM10/12/2010 10:41:54 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kicker zx 700 5 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info