Bedienungsanleitung Klipsch Gallery Series (Seite 4 von 20) (Deutsch, Englisch, Französisch, Portugiesisch, Spanisch)

584780

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

SPEAKER/SOUNDBAR ON-WALL INSTALLATION

If you mount your G-12,G-16,G-28 speakers or G-42 soundbar on a wall, do

not attach the pedestals. Determine a suitable location for each speaker to

wall-mount and complete all wiring to all speaker positions before mounting

speakers to the wall. Do not ceiling-mount.

1. If you have the G-28 or G-42, use included template and choose mount

position for the speaker (horizontal or vertical). Pin template to wall, mak-

ing sure it is level (when horizontally mounting) or plumb (when vertically

mounting) and positioned correctly, centered with the TV’s center points for

example. Mark on wall the pilot hole locations through the template and

remove template. If you have the G-12 or G-16, mark on wall 2 pilot hole

points 9.26”apart for the G-12 or 13.25”apart for the G-16 (make sure

the points are lined up so that the speaker hangs straight up and down verti-

cally or level horizontally). For all speakers, Leave a minimum of one inch

space between speaker cabinet and TV. Keep in mind that, when mounted,

the speaker will “lock” into position 5/16” lower than where the pilot holes

are drilled.

2. Pre-drill pilot holes in marked locations. If drilling into a wall stud (ideal) it is

recommended to use #10 mounting screws (not included) to mount the

speaker bracket (G-28 and G-42) or the speaker itself (G-12 and G-16).

If there is no stud where a pilot hole is located, install wall anchors (not

included) into the pilot holes to hold the bracket or speaker instead. Wall

anchors should be rated to at least 6 pounds (G-12 and G-16) or 12 pounds

(G-28 and G-42).

3. If vertical wall-mounting, feed speaker wire into speaker bottom area

and attach each wire to appropriate screw-terminal binding post (See

Diagram 2). If horizontal wall-mounting, feed speaker wire to channel(s)

that start on the back center part of the speaker, then continue run-

ning wire through the channel(s) and attach each wire to the appropri-

ate screw-terminal binding post the same as if vertical mounting. (See

Diagram 3) (Note: using speaker wire larger than 18 gauge may

not allow wire(s) to completely ﬁt in channels). If needed, stick the

included adhesive strip on a point over the channel to hold the wires

in place in the channel. To change the Klipsch logo direction on the

speaker front gently pull out one side of it and rotate 45˚.

4. Gently push the speaker onto the two tabs on the mounted bracket through

its keyholes (G-28 and G-42) or onto the two screws in the wall (G-12 and

G-16) and push 5/16” down to lock into position.

CONNECTING

G-12,G-16,G-28 Connection - Using 16-gauge or larger speaker wire, con-

nect the RED “positive” (+) terminal of the LEFT speaker to the RED “positive”

(+) terminal of your ampliﬁer’s LEFT channel. Connect the BLACK “negative” (-)

terminal of the left speaker to the BLACK “negative” (-) terminal of your ampliﬁer’s

left channel. Repeat this procedure for connecting all remaining speakers to the

appropriate ampliﬁer channels.

G-42 soundbar Connection - Since this speaker contains the LEFT, RIGHT and

CENTER channels, connect each one of these channels from your ampliﬁer as

above to the designated “Left”, “Right” and “Center” terminals on the G-42.

Make sure that no bare wires from any of the connections touch each other or

any other terminals as this could cause a short and damage your equipment.

SPEAKER CARE AND CLEANING

Your Klipsch Gallery™ Speaker has a durable ﬁnish that should only require dry

dusting or cleaning with a dry cloth. Avoid the use of abrasive or solvent-based

cleaners and harsh detergents. The unique grille for the speaker consists of a

piece of sheer rectangular cloth with metal rods along two sides. It is held in

place by magnets imbedded in a slot on each side of the rear of the cabinet.

Carefully pull the metal rod away from one side, then the other to remove

grill. The grill is designed to be as lightweight and acoustically transparent as

possible so there is no rigid framework behind it. Because of this, it might be

necessary to “smooth” the cloth once the grill is attached to the cabinet by us-

ing two thumbs to pull the cloth taught from top to bottom (or side to side if unit

is mounted horizontally).

DIAGRAM 1

DIAGRAM 2

DIAGRAM 3

Front Left

Front Right

Back Surround

Left

Back Surround

Right

Surround

Right

Surround

Left

Speaker Hookup

Center

HDMI Out

HDMI 1 HDMI 2 HDMI 3

TAPE TV DVD

Monitor

Out

Video

Out In In In In

CBL/SAT

Sub Pre Out

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klipsch Gallery Series Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info