Bedienungsanleitung Klipsch IC-SW-8T (Seite 2 von 6) (Englisch)

584724

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

3. To install the tilebridge, fold the rail side of the ring back

upon itself using the spring tensioner on the reinforcement ring

to allow insertion into the cutout hole. Once it is inserted into

the cutout hole, release the reinforcement ring such that it

unfolds back to its normal position. Position tilebridge over

cutout hole.

4. The wiring compartment is intended as a termination point

for the audio circuit. Access to this compartment is gained by

removing the terminal cover located on the back of the

speaker. The terminal cover will accept the appropriate

conduit/wire adapter (provided). Feed wires through

conduit/wire adapter and connect to the input terminal

according to the desired operation mode. Be sure to observe

proper polarity. Replace the terminal cover and tighten the

conduit/wire adapter to secure the wire.

Caution: When connecting 70V or 100V dist r i b u t e d

line systems, ta ke care to ensure proper te rm i n a l

connection. Connection to the low impedance te rm i -

nal could re s u l t in speaker damage, amp l i f i e r

d a m a g e, or both.

Thank you for purc hasing yo u r

K l i p s c h IC-SW-8T in-ceiling subwo o f e r .

The IC-SW-8T in-ceiling speaker is designed for music reinforce-

ment applications. Unobtrusive, these loudspeakers are engi-

neered for easy, versatile installation.

The IC-SW-8T features a transformer-less design for 70.7V/100V

distributed-line systems. Some of the benefits of this design are:

Elimintation of transformer saturation at high output levels,

elimination of transformer insertion losses, improved bandwidth

(particularly at low frequencies), and improves power transfer to

the loudspeaker at low frequencies. For applications where 4

ohm mono or 8 ohm stereo operation is required, the mode of

operation can be selected by using an optional connection

located on the back input terminal and by properly setting the

rotary switch located under the grill.

Before installing your speakers take a moment to check the

contents of the cartons and make sure nothing has been

damaged in transit.

Conte nt s Descr iption Q

UA N T I T Y

Speaker Module 1

Grille 1

Reinforcement Ring 1

Rails 2

Cardboard Cutout Template and Paint Mask 1

Screws (Attach Rails to Reinforcement Ring) 2

8 "

Adapter Fittings 1

2 "

Adapter Fittings 1

Install ation Guidel ines

The IC-SW-8T includes a tilebridge for use when installing

the loudspeaker into suspended ceilings or wherever additional

reinforcement of the ceiling material is required. The tilebridge

and loudspeaker are designed such that installation may be

accomplished where access above the ceiling is not possible

or may be difficult.

I n s t a l l a t i o n

The tilebridge is composed of three parts—a reinforcement ring

and two rails. The two rails should be attached to the

reinforcement ring using the two included screws as shown below.

Caution: Be sure to comp l y with any and all building codes

in your are a .

2. To install your IC-SW-8T cut out a hole in the ceiling using either

the cardboard cutout template provided with your speakers or

consult the measurements below. Pull wiring through hole.

I C - S W - 8 T S U B W O O F E R

I C - S W- 8T

" R o u n d

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klipsch IC-SW-8T Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info