Bedienungsanleitung Klipsch KPT-801 (Seite 3 von 4) (Englisch)

584786

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

KPT-801

The Klipsch KPT-801 is a two-way design using a high perfor-

mance bass driver for the low frequencies. A Tractrix Horn

with a 90° x 90° coverage pattern is attached to a 1” diam-

eter compression driver for clean and efﬁcient reproduction

of the high and midrange frequencies.

WALL MOUNTING

Included with your speakers are “C” style mounting brackets

constructed of powder-coated zinc. These brackets attach to

the speaker with the supplied low proﬁle knobs that thread

onto the top and bottom studs protruding from the cabinet.

This allows the speaker to be angled to the left or right when

mounted vertically, or up and down when mounted horizon-

tally. When mounting horizontally, lock nuts are provided for

both studs for optimum speaker stability.

After determining the desired location and orientation of

your speakers, remove the bracket from the loudspeaker

and use it as a template to mark the location of the mount-

ing holes. Check the alignment of the holes with a torpedo

level before drilling the pilot hole. Please observe local and/

or federal codes in securing the bracket, especially when

suspending objects above people’s heads. Once the bracket

is secured, afﬁx the speaker to the bracket with the supplied

knobs. Be sure to leave enough clearance between the end of

the bracket and any adjacent wall or ceiling for installation of

the knobs.

If a wall stud is not available, use the appropriate type of

drywall or masonry anchor to support the weight of the

speaker, allowing for a generous safety margin. Please con-

sult your dealer, custom installer or building contractor in

these situations.

You may also use an optional wall or ceiling mount that will

ﬁt the provided 3/8” – 16 inserts.

PLACEMENT

CONNECTIONS

When making any type of speaker wire connection, be sure

to observe proper polarity. Most speaker wire and connec-

tors are color-coded. Typically, red is positive (+) and black is

negative (–), or ground. It does not matter which wire con-

ductor is connected to the positive or negative connection of

your equipment as long as it is consistent.

TYPES OF CONNECTORS

Your speaker is equipped with barrier strip connectors for

inputs. Make sure that there is no metal-to-metal contact

between the two lugs. Failure to observe this precaution at

either end of the connection can result in ampliﬁer malfunc-

tion or damage.

SCREEN

Last 25% of wall or 25 ft.

The ﬁrst surround 1.5 meters from the back wall.

Last surround within .25 (25%) of the length of the side.

Each surround (after ﬁrst on back wall 1.5 meters from wall)

placed 3 meters from each other.

100 ft. Wall

On the back wall, the ﬁrst surrounds are

placed 1.5 meters from the side walls, then

each surround is placed 3 meters from each

other until they meet in the middle. (Even

space them) so you are as close to 3 meters

distance between them as possible.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klipsch KPT-801 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info