Bedienungsanleitung Klipsch LF-10 (Seite 12 von 12) (Englisch)

584802

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Types of Connections

Your subwoofer may be installed using either “SPEAKER LEVEL” or “LINE LEVEL” connections;

both are not required. The LFE connection, however, is an optional line level connection that can be

used in conjunction with either type of hookup. Refer to the “LFE/BYPASS IN” and “BASS MAN-

AGEMENT” sections for more detail. You can connect the subwoofer so that your main speakers

will reproduce a full range signal or a limited range (bass ﬁltered) signal. Speaker level connections

are used when connecting to a receiver or integrated ampliﬁer that lacks line level subwoofer or pre-

amp output jacks. Line level connections are often the best choice when connecting the subwoofer to

a pre-amp/processor and power ampliﬁer or integrated ampliﬁer that possesses main channel pre-amp

or subwoofer outputs. The type of connection used depends upon the capabilities of your equipment

and your performance goals.

Speaker Level Connections

MAIN SPEAKERS FULL RANGE

Connect your main speakers and the left/right “SPEAKER IN” terminals of the subwoofer to the

corresponding main speaker outputs of your receiver/ampliﬁer. Refer to the righthand side of Figure A.

If your electronics are so equipped, the subwoofer could be connected separately to the

receiver/ampliﬁer’s speaker “B” outputs. If the subwoofer is located closer to your main speakers

than your electronics, you can connect the main speakers to the “SPEAKER IN” terminals of the

subwoofer and connect only the subwoofer to the receiver/ampliﬁer as described above. Please consult

your dealer for details regarding connection of multiple speaker cables to a common set of speaker

outputs. For optimum performance, use equal lengths (left and right inputs) of the same high quality

speaker cable that you are using to connect your main speakers. Consult your Klipsch dealer for spe-

ciﬁc recommendations. Refer to “About Speaker Wire Connections” for more detail.

MAIN SPEAKERS LIMITED RANGE

If a bass limited signal will be sent to your main speakers, connect them to the “SPEAKER OUT”

terminals on the subwoofer instead of to your ampliﬁer. Refer to the righthand side of Figure B.

The high pass ﬁlter on these outputs will remove the bass frequencies below 100Hz from your main

speakers, lowering distortion and increasing dynamic range. Refer to the “LOW PASS” section for

more detail.

Note: Do not connect another subwoofer to these outputs as they are high pass ﬁltered (bass

frequencies removed).

About Speaker Wire Connections

Be sure to observe proper polarity when making connections between the subwoofer and the ampliﬁer

(+ to + and - to -). If the polarity of one of these wires is reversed, the output of the subwoofer will

be diminished. Most speaker wire is color-coded or has some distinguishing feature differentiating the

two conductors. Speaker wire connectors on most loudspeakers and ampliﬁers are also color-coded.

Typically, RED is positive (+) and BLACK is negative (-), or ground. It does not matter which wire

conductor is connected to the positive or negative terminals of your equipment as long as

you are

consistent. Be sure that the connections from the ampliﬁer to all of the speakers in your system

are con-

nected in a like manner. If this is not done, the quantity of bass will be reduced and the stereo image

will be compromised. Be careful to avoid excess bare wire or loose strands of wire at the connections.

This could cause a shorting condition between adjacent positive and negative terminals that could

damage your equipment.

Line Level Connections

These connections should be made using high quality shielded interconnect cables terminated with

RCA phono plugs. These cables should be as short as possible and kept away from noise generating

electrical equipment such as digital electronics or electric motors. Consult your Klipsch dealer for

speciﬁc cable recommendations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klipsch LF-10 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info