Bedienungsanleitung Konig Electronic KN-INDUC-20 (Seite 4 von 80) (Alle Sprachen)

570445

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

English

Use

Setting the power

• Press the function button until the power indicator

comes on. The display shows “1600”.

• Turn the setting dial clockwise to increase the power.

• Turn the setting dial counterclockwise to decrease the

power.

Setting the temperature

• Press the function button until the temperature

indicator comes on. The display shows “200°”.

• Turn the setting dial clockwise to increase the

temperature.

• Turn the setting dial counterclockwise to decrease the

temperature.

Setting the timer

• Press the function button until the timer indicator

comes on. The display shows “00:00”.

• Turn the setting dial clockwise to set the hours.

• Turn the setting dial counterclockwise to set the

minutes (1-minute steps).

• Press the function button to conrm or wait until the

display stops ashing.

• At the end of the countdown, a beep will sound and

the device will go to standby mode.

To cancel the function:

• Press the on/o button to go to standby mode. The

timer indicator goes o.

• Press and hold the function button to resume

operation with the set power or temperature settings.

The timer indicator goes o.

Hints for use

• Insert the mains plug into the wall socket. A beep will

sound and the indicators ash once. The on/o

indicator starts to ash. The device is in standby mode.

• Place the cookware in the centre of the cooking zone.

• Press the on/o button to switch on the device. The

on/o indicator lights continuously. The display shows

“----”.

• Set the device according to your cooking requirements.

• After use, press the on/o button to set the device to

standby mode. The on/o indicator starts to ash.

• Remove the mains plug from the wall socket.

• Allow the device to cool down completely.

Error codes

Description Solution

Internal circuit error.

(1) Use suitable cookware.

(2) Switch o the device, allow

the device to cool down

completely and switch the

device on again.

No cookware or unsuitable

cookware used.

Top plate overheating.

Internal overheating.

Contact the service centre.

Overvoltage.

Undervoltage.

Open-circuit error or

short-circuit error

(top plate sensor).

Open-circuit error or

short-circuit error

(IGBT sensor).

Cleaning and maintenance

Warning!

• Before cleaning or maintenance, switch o the device,

remove the mains plug from the wall socket and wait

until the device has cooled down.

• Do not use cleaning solvents or abrasives.

• Do not immerse the device in water or other liquids.

• Do not attempt to repair the device. If the device does

not operate correctly, replace it with a new device.

• Clean the outside of the device using a soft, damp

cloth. If necessary, use a little neutral detergent.

Thoroughly dry the outside of the device with a clean,

dry cloth.

• Clean the ventilation openings using a soft brush.

Technical data

Power settings

300 W / 600 W / 900 W / 1200 W /

1400 W / 1600 W / 1800 W / 2000 W

Temperature settings

60 °C / 80 °C / 100 °C / 120 °C

140 °C / 160 °C / 180 °C / 200 °C

Timer settings 1 minute ~ 11 hours / 59 minutes

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Konig Electronic KN-INDUC-20 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info