Bedienungsanleitung Konig Electronic TVS-KN-AVS502 (Seite 2 von 36) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

570563

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Installation procedure

Step 1:

Invert the display and place it on a soft and ﬂ at surface. Locate the mounting points on

the back of the display.

Many LCD manufacturers conform to VESA standards. The VESA standard deﬁ nes

the physical mounting interfaces. The LCD mount conforms to VESA 75/100/200/400

patterns.

Plasma monitors come with a random set of holes.

Note! Do not over tighten the screws. This may cause damage to the display or

bracket.

Before you begin, determine the desired mounting location.

Step 2:

Assemble the wall plate using the hardware and wrenches provided.

Note! Tighten screws uniformly to prevent distortion that might affect the assembly

process. Do not tighten with excessive force. Failure to follow these instructions may

cause excessive stress to the screws, greatly reducing their strength.

Solid concrete wall assembly: Carefully inspect the area where the LCD\Plasma\

Projector mount is to be installed. Check for any damage or loose cement.

Caution! When drilling holes in a cement wall or wooden studs, be absolutely sure there

are no water pipes or electrical wiring behind the wall. Use the wall plate to mark the

positions of the drilling holes.

Drill holes 3” deep using a (10 mm) masonry drill bit. Insert the plastic anchors into the

hole and tap ﬂ ush until the washer is even with the concrete surface. Place the back plate

onto the concrete surface and slowly tighten each nut onto its respective anchor.

Wood studs assembly:

Use a stud sensor (sold separately) to locate framing near the desired mounting position.

Note! Framing beams are typically 1-1/2”- 2” wide and spaced 16” on center. We

recommend locating more than one stud to ﬁ nd a trend in stud spacing. Using a sharp

device penetrate the drywall to identify the true center of the stud. Using the wall plate

base as a template, position the wall plate base vertically. Mark the hole position on

the wall, making sure you use the center screw holes. Use a level to check horizontal

alignment of marks.

Step 3:

For tilting models, gently pull the left and the right upper edges of the display to extend

the mount to its desired display tilting angle. Using a Phillips screwdriver, adjust the tilt

mechanism to its desired position. LCD mount models are designed to maintain their

tilting angle by using ﬁ nger tips on the back of the monitor. Keeping the display far from

the tilting mechanism, turn the Philips screw to its desired angle.

Step 4:

Once the mounting of the display is completed, you can tills move the display from side to

side to optimize the ﬁ nal position of the display. Gently slide the unit from left to right over

the steel rods on the wall plate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Konig Electronic TVS-KN-AVS502 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Konig Electronic TVS-KN-AVS502

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info