Bedienungsanleitung Korg AX10A (Seite 4 von 39) (Deutsch, Englisch, Französisch)

488492

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

Quick Start

Before you make connections with any external

devices, turn all volumes to the minimum position

and turn off the power.

1. If you will be powering the AX10A with batteries,

open the battery compartment located on the

bottom panel, and install four AA alkaline

batteries (sold separately). If you will be powering

the AX10A with the separately sold AC adaptor,

connect the AC adaptor to the rear panel DC9V

connector (the power will turn on).

2. Set the INPUT L/H switch to the appropriate

position for the output of your guitar. Use the “H”

position if your guitar has a high output pickup, or

the “L” position if your guitar has a low output

pickup.

3. Connect your guitar to the AX10A’s INPUT jack. If

you are using batteries, the power of the AX10A

will turn on at this point.

4. If you’re connecting the AX10A to a PA system or

guitar amp, set the AMP/LINE switch to “AMP”. If

you’re connecting it to headphones, mixer or a

recorder, set this switch to “LINE”.

5. Connect the AX10A’s OUTPUT jack to the INPUT

of your guitar amp or recorder. If you want to use

headphones, connect them to the OUTPUT jack.

6. Turn on the power of the connected equipment,

and raise the volume to an appropriate level. You

can also use the AX10A’s MASTER buttons to

adjust the volume.

7. Press the program select switches to change

programs.

TIPS

The AX10A has 40 preset programs (01–94) and 40

user programs (0.1–9.4). With the factory

settings, the user programs contain the

same contents as the preset programs.

8. You can control the pedal effect by using the

expression pedal. The pedal is active when the

PEDAL LED at the upper left of the pedal is lit. If

this LED is dark, advance the pedal all the way

forward to make the LED light. Now the pedal will

be active.

Editing a Sound

9. Turn the MIC & BODY selector to select your

desired sound, and use the DEPTH buttons to

adjust the depth. Use the tone control knobs to

adjust the tone and volume. If acoustic feedback

occurs, you can turn the NOTCH selector to

suppress the frequency at which feedback tends

to occur.

Editing and Effect

10. Adjust the chorus or ambience effect as desired.

Use the AMB (CHORUS) buttons to adjust the

depth of the ambience effect. By holding down

the FUNCTION button while pressing the AMB

(CHORUS) buttons you can adjust the depth of

the chorus effect. With a setting of “00” there will

be no effect. The delay/reverb time of the

ambience effect can be adjusted by pressing the

TAP button at the desired timing interval.

11. To adjust the pre-effect located in front of Mic &

Body, press the PRE FX button to select an

effect, and use the VALUE buttons to adjust it.

This concludes our brief introduction to the

AX10A. This manual contains much more

information about the AX10A, so please read it to

ensure that you are taking full advantage of all its

capabilities.

2 1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg AX10A Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info