Bedienungsanleitung Korg AX10B (Seite 5 von 40) (Deutsch, Englisch, Französisch)

488493

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Quick Start

Before you make connections with any external

devices, turn all volumes to the minimum position

and turn off the power.

1. If you will be powering the AX10B with batteries,

open the battery compartment located on the

bottom panel, and install four AA alkaline

batteries (sold separately). If you will be powering

the AX10B with the separately sold AC adaptor,

connect the AC adaptor to the rear panel DC9V

connector (the power will turn on).

2. Set the INPUT L/H switch to the appropriate

position for the output of your bass. Use the “H”

position if your bass has a high output, or the “L”

position if your bass has a low output.

3. Connect your bass to the AX10B’s INPUT jack. If

you are using batteries, the power of the AX10B

will turn on at this point.

4. If you are connecting the AX10B to a bass amp,

set the AMP/LINE switch to “AMP”. If you are

connecting the AX10B to headphones, a recorder,

or a mixer, set this switch to “LINE”.

5. Connect the AX10B’s OUTPUT jack to the INPUT

of your bass amp or recorder. If you want to use

headphones, connect them to the OUTPUT jack.

6. Turn on the power of the connected equipment,

and raise the volume to an appropriate level. You

can also use the AX10B’s MASTER buttons to

adjust the volume.

7. Press the program select switches to change

programs.

TIPS

The AX10B has 40 preset programs (01~94) and 40

user programs (0.1~9.4). With the factory settings,

the user programs contain the same

contents as the preset programs.

8. You can control the pedal effect by using the

expression pedal. The pedal is active when the

PEDAL LED at the upper left of the pedal is lit. If

this LED is dark, advance the pedal all the way

forward to make the LED light and the pedal will

be active.

9. Editing the sound

Use the AMP TYPE selector to select an amp

type, and use the various control knobs to adjust

the gain, tone, and volume etc.

10. Editing an effect

If you want to edit the modulation effect or

ambience effect (located after the amp), use the

MODULATION selector or AMBIENCE selector to

select the desired effect, and use the DEPTH

buttons located below the selector to adjust the

effect depth etc. You can also adjust the speed

etc. of a modulation effect by holding down the

FUNCTION button and pressing the DEPTH

buttons (which act as the SPEED buttons). For the

ambience effect, you can set the delay or reverb

time by pressing the TAP button at the desired

interval.

11. To edit the pre-effect located before the amp,

press the PRE FX button to select an effect, and

use the VALUE buttons to make adjustments.

This concludes our brief introduction to the

AX10B. This manual contains much more

information about the AX10B so please read it to

ensure that you are taking full advantage of all its

capabilities.

10 10

2 1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg AX10B Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info