735585
2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
-2-
Installaon
Pin layout
C N
1 Lamp (~230 V)
LED light - ashing
2 NC
3 Horn (~230 V)
LED light - connuous
+ sound
CO2 CONTROL installaon plan
5
6
4
Final assembly
4. Insert the screws
There are protrusions ② on the right and le sides of the housing
which can be removed to install the cable guide.
5. Cable installaon
Guide the cable through the secured cable guide into the unit unl
the insulaon layer can be seen in the unit, then screw the cable
guide ght.
6. Preparaons for installaon
The plug connecon ③ can be unplugged for wiring.
7. Installaon plan
The wires must be connected in accordance with the installaon
plan [4] (see below).
8. Aach a strain relief device
Insert the cable e into the opening and secure this to the
stranded wire.
9. Fit the lens
Once the alarm unit is correctly wired, the indicator lens can
be connected to the connector cable ④.
10. Aach the lens [5]
Aach the lens to the housing. When doing so, ensure that
the four latching cuts are inserted into the housing.
11. Tighten the lens [6]
Turn the lens to the right unl this is securely fastened.
12. Secure the lens
To further secure the lens, a locking screw with an O-ring can
be screwed into the opening provided for that purpose
on the right side of the housing.
6
3
4
3
2
2
Imprint
Copyright to this documentaon has been asserted by KUNDOxT GmbH. This documentaon may not be altered, expanded, reproduced or disclosed to third
pares without the prior wrien approval of KUNDOxT GmbH. Design and equipment subject to change.
5
Control line
CO2 CONTROL
Switching unit Signal unit Sensor unit 2 Sensor unit 1 2 x distributors Alarm unit Superordinate
control system
CO2 CONTROL
PA AM /
PA AM PLUS
230 V (AC)
Sum alarm out
Operaon out
Malfuncon out
Pre alarm out
Main alarm out
A1
A2
E1
E2
E3
E4
E5
1 L in
2 N in
3 N
4
5
6
7
8
9
10
11
12
13
14
BK
WH
BU
BN
Horn out
Lamp out
C
3
1
N out
BK
WH
BU
BN
BK
WH
BU
BN
BK
WH
BU
BN
BK
WH
BU
BN
BK
WH
BU
BN
BK
WH
BU
BN
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kundo xT Co2 Control Alarm wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Kundo xT Co2 Control Alarm

Kundo xT Co2 Control Alarm Installationsanweisung - Deutsch - 2 seiten

Kundo xT Co2 Control Alarm Installationsanweisung - Holländisch - 2 seiten

Kundo xT Co2 Control Alarm Installationsanweisung - Französisch - 2 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info