Bedienungsanleitung La Crosse WS9032 (Seite 3 von 16) (Englisch)

606455

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

1. Remove the cover.

2. Insert the batteries, observing the correct polarity (see marking).

3. Replace the battery cover.

Note:

In the event of changing batteries in any of the units, all units need to be

reset by following the setting up procedures. This is due to a random

security code assigned by the transmitter at start-up. This code must be

received and stored by the Weather Station in the first 3 minutes of power

being supplied to the transmitter.

BATTERY CHANGE:

It is recommended to replace the batteries in all units on an annual basis to ensure optimum

accuracy of these units.

Please participate in the preservation of the environment. Return used

batteries to an authorized depot.

SETTING UP

WHEN ONE TRANSMITTER IS USED

1. First, insert the batteries in the transmitter (see “How to install and replace batteries

in the Termo-hygro outdoor transmitter” above).

2. Within 2 minutes of powering up the transmitter, insert the batteries in the Temperature

Station (see “How to install and replace batteries in the Weather Station” above).

Once the batteries are in place, all segments of the LCD will light up briefly and a short

signal tone will sound. Following the indoor temperature/humidity and the time as 0:00

will be displayed. If these information are not displayed on the LCD after 60 seconds,

remove the batteries and wait for at least 60 seconds before reinserting them. Once

the indoor data is displayed user may proceed to the next step.

3. After the batteries are inserted, the Weather station will start receiving data signal from

the transmitter. The outdoor temperature and humidity data should then be displayed

on the Weather station. If this does not happen after 2 minutes, the batteries will need

to be removed from both units and reset from step 1.

4. In order to ensure sufficient 868 MHz transmission however, the distance between the

Weather Station and the transmitter should not be more than 100 meters (see notes on

“Positioning” and “868 MHz Reception”).

Note:

In the event of changing batteries of the units, ensure the batteries do not spring free from

the contacts. Always wait at least 1 minute after removing the batteries before reinserting,

otherwise start up and transmission problems may occur.

WHEN MORE THAN ONE TRANSMITTER IS USED

1. User shall remove all the batteries from the Weather Station and transmitters, and wait

60 seconds.

2. Insert the batteries in the first transmitter.

3. Within 2 minutes of powering up the first transmitter, insert the batteries in the Weather

Station. Once the batteries are in place, all segments of the LCD will light up briefly

and a short signal tine will sound. Following the indoor temperature/humidity and the

time as 0:00 will be displayed. If these information are not displayed on the LCD after

60 seconds, remove the batteries from both units and wait for at least 60 seconds

before reinserting them.

4. The outdoor temperature and humidity data from the first transmitter (channel 1)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

La Crosse WS9032 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info