Bedienungsanleitung Laserliner DigiLevel Pro 30 (Seite 5 von 19) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch)

646122

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

DigiLevel Pro 30/60/120

Keypad

1. (REF) – Angle reference value setting

2. ( ) – ON / OFF switch

3. (

)

) ) – Acoustic signal on/off

4. (MR) – Memory retrieval

5. (UNIT) – Unit of measurement selection

(° degrees / % / IN/FT)

6. (M) – MEMORY function

Display

7. Slope direction

8. Slope angle

9. Current memory position (M1 – M9)

10. Battery charge

DigiLevel Pro 30/60/120

11. Vertical vial

12. Horizontal vial

13. Magnets

14. Measuring surface, 30 / 60 / 120 cm

15. Point laser ON / OFF

16. Tripod threads, 1/4"

Rear

17 . Battery compartment

Inserting batteries:

Open the battery compartment (17) on the rear of the DigiLevel and

insert two new batteries (type AAA/LR03) in the manner indicated

by the installation symbols. Ensure correct polarity. The symbol (10)

indicates the level of battery charge.

Digital electronic spirit level with vertical and horizontal angle display and

point laser (650 nm).The slope can be indicated in degrees, IN/FT or percent

on the display.An acoustic signal indicates the horizontal or vertical position.

The slope memory enables angles to be projected elsewhere, while

the separate measurement memory allows up to 9 measurements results

to be stored and retrieved. Milled measuring surfaces, powerful ﬁ xing

magnets, as well as additional vertical and horizontal vial, illuminated display.

Calibration function for increased accuracy and adaptation to measuring

surface.

Switching on and measuring:

The DigiLevel Pro can measure angles continuously to 360°.

• Switch the DigiLevel Pro on using the on/off switch (2).

• The current operating temperature in °C is shown for a few seconds.

• The slope angle is shown in the display (8). If slopes are measured

overhead, the direction of display adjusts automatically.

• The current slope direction is also shown by the symbol (7).

Selection of unit of measurement:

• Button (5) allows the desired unit of measurement to be selected

(° degrees, %, IN/FT)

Changing the angle reference value:

• With button (1), it is possible to transfer angles elsewhere. To do so,

set the device to the desired slope and press button (1). The display will

then change to “0.0”, and the desired reference angle is now set.

The slope can now be transferred to other objects.

IMPORTANT: When all the slopes have been transferred, make sure

to deactivate the new angle reference value. To do this, switch off

the device by pressing the on/off switch (2) for at least 3 secs. Only

then will the value be reset itself to the measuring surface (14).

Acoustic signal:

• The acoustic signal can be switched on or off with button (3).

• When the angle of slope stands at 0°, 45°, 90° or the most recently

stored value, this is indicated by an acoustic signal.

NOTE: When working with a changed angle reference value, the

acoustic signal is activated on reaching the new reference value

(0°, 45°, 90° display).

97108

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Laserliner DigiLevel Pro 30 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info