Bedienungsanleitung Lenco IR-2002 (Seite 5 von 57) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

534766

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

SET UP & CONNECTI O N

Mains Connection

1. Insert the DC power jack of the AC/DC adaptor to the DC IN socket

located at the back of the unit.

2. Plug the AC/DC Adaptor to the AC mains outlet.

Network Connection

Wired network

1. Check first of all whether the control lamps (LINK/ACT) of your LAN connection or your router light up.

2. Use an Ethernet cable with RJ45 connector to connect the NETWORK socket of the radio with the

LAN port of your router.

3. Proceed for the operation as described in the below“GETTING STARTED”. But no need to run

throughthe setup wizard

Note: Information on the LAN connection can be obtained from the user manual of the router

manufacturer.

Wireless network

1. Check first of all whether the control lamps (LINK/ACT) of your WLAN connection or your router light

up.

2. Proceed for the operation as described in the below “GETTING STARTED”. It is highly recommended

to run through the setup wizard in the system settings section.

Note: Information on the WLAN/WiFi network connection can be obtained from the user manual of the

router manufacturer.

Walls or other obstacles may influence the WiFi range. Try to find the best location to avoid

interruption and interference while operating.

GETTING STARTED

Press the “standby icon” button once to switch on the radio, the display will show the main menu. To go to

a function or open a sub-menu, rotate the SELECT control followed by pressing on it to confirm. Each

function is selected via a menu consisting of several levels.

Main menu

The following modes can be selected in the main menu:

Internet radio, Music player, FM radio, AUX in, Sleep, Alarms, System settings

To select your desired function, rotate the SELECT control followed by pressing on it to confirm.

SYS T E M SETTINGS

Set up wizard

The setup wizard is available in the system settings section, you can run through this to configure

settings for date/time and network, once this has finished, your radio is ready to use.

Note: No need to run through the setup wizard if a wired network is used.

- 12/24 hour display

To select your preference between 12 or 24 hour clock display format - rotate the SELECT control

followed by pressing on it to confirm.

- Time/Date

The time and date can be manually set or automatically via the network, or FM.

Auto update

The auto update works with data sent over, FM or the Internet. The clock is only updated when in

a corresponding mode, so it is recommended to select a mode that you use regularly.

1. Select auto update from , FM or Network.

2. Select the appropriate time zone if the auto update is done by the Internet.

3. If your country uses daylight saving, the automatically update time may be wrong by one hour. Set

the daylight savings to ON when daylight savings are in effect.

Manual set

1. If “No update” is selected, the wizard will prompt you to set the

time and date manually. The date and

time are displayed in dd-mm-yyyy and hh:mm AM/PM format.

2. The value to be set will flash, rotate the SELECT control to

adjust the value followed by pressing on it

to go for the next setting, first set the date then finally the time.

◊Network

The unit is compatible to all standard network protocols and encryption methods, including Wi-Fi

Protected Setup (WPS). In case of an unencrypted network, the unit will automatically establish

connection and no further settings are necessary.

Standard encrypted network

1. To enter the network key (password), rotate the SELECT control to move the cursor through the

characters to be selected and press on it to confirm.

2. The key that is entered will be displayed in the upper part of the display.

00:00

00/00/0000

UK-4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lenco IR-2002 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info