601898
4
Zoom out
Zoom in
Vorherige Seite
1/25
Nächste Seite
4
ASSEMBLY
Drive belt:
The belt and turntable platter have been installed properly at factory, but the belt
may be loose during transportation. If so, the following procedures will be taken for
belt installation by yourself.
A. Remove the E ring clip from the turntable shaft, and then release the turntable
platter from the shaft
B. Put the drive belt on the inner rim of the turntable platter and pull it through the
hole
C. Hold the belt with your fingers and place the belt onto the motor pulley as
shown in the drawing.
D. Clip the E ring on the shaft and place the rubber mat onto the turntable platter.
Caution:
1. Make sure that the drive belt is not twisted or distorted.
2. Do not oil. Oil splashes will make the belt slippery.
Adjustment of the platter speed:
1. Set the arm lift lever to the up position.
2. Set the speed select switch to either 33’ or 45 according to the speed of the
record to be played.
3. Release the arm clip and move the tonearm toward the turntable platter/ The
turntable will start revolving.
4. Observe the appropriate strip of strobe calibration dots.
5. If the strobe dots appear to flow to the right it means the platter is revolving
slower than the rated speed. If the strobe dots appear to flow to the left, then
the platter is revolving faster than the rated speed. There are two speed
adjustment holes on the bottom. Adjust in until the strobe dots appear to be
stationary.
6. After the platter speed has been adjusted correctly return the tonearm to the
arm rest and fix the arm clip.
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Lenco L-84 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Lenco L-84

Lenco L-84 Bedienungsanleitung - Deutsch - 27 seiten

Lenco L-84 Bedienungsanleitung - Holländisch - 26 seiten

Lenco L-84 Bedienungsanleitung - Französisch - 27 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info