Zoom out
Zoom in
Vorherige Seite
1/27
Nächste Seite
OWNER’S MANUAL
AIR CONDITIONER
Please read this manual carefully before operating
your set and retain it for future reference.
www.lg.com
TYPE : Multi
The equipment complies with requirements of the Technical
Regulation, in terms of restrictions for the use of certain dangerous
substances in electrical and electronic equipment.
P/NO : 3828A20394M
ENGLISH
ITALIANO ESPAÑOL
FRANCAIS DEUTSCH
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Inhalt der Seiten


  • Page 1

    ENGLISH
    ITALIANO
    ESPAÑOL
    FRANCAIS
    DEUTSCH

    OWNER’S MANUAL

    AIR CONDITIONER
    Please read this manual carefully before operating
    your set and retain it for future reference.
    TYPE : Multi

    The equipment complies with requirements of the Technical
    Regulation, in terms of restrictions for the use of certain dangerous
    substances in electrical and electronic equipment.

    www.lg.com
    P/NO : 3828A20394M



  • Page 2

    Room Air Conditioner Ownerʼs Manual

    TABLE OF CONTENTS
    Safety Precautions.........................3

    FOR YOUR RECORDS
    Write the model and serial numbers here:
    Model #

    Prior to Operation ..........................7

    Serial #
    You can find them on a label on the side of each unit.
    Dealer's Name

    Introduction ....................................8

    Electrical Safety .............................9

    Operating Instructions.................10

    Maintenance and Service ............23

    Date Purchased
    ■ Staple your receipt to this page in the event you need
    it to prove date of purchase or for warranty issues.

    READ THIS MANUAL
    Inside you will find many helpful hints on how to use
    and maintain your air conditioner properly. Just a little
    preventive care on your part can save you a great deal
    of time and money over the life of your air conditioner.
    You'll find many answers to common problems in the
    chart of troubleshooting tips. If you review our chart of
    Troubleshooting Tips first, you may not need to call
    for service at all.

    PRECAUTION
    • Contact the authorized service technician for
    repair or maintenance of this unit.
    • Contact the installer for installation of this unit.
    • The air conditioner is not intended for use by
    young children or invalids without supervision.
    • Young children should be supervised to ensure
    that they do not play with the air conditioner.
    • When the power cord is to be replaced,
    replacement work shall be performed by
    authorized personnel only using only genuine
    replacement parts.
    • Installation work must be performed in
    accordance with the National Electric Code by
    qualified and authorized personnel only.

    2 Room Air Conditioner



  • Page 3

    Safety Precautions

    To prevent the injury of the user or other people and property damage, the following instructions must be
    followed.
    ■ Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified
    by the following indications.

    WARNING

    This symbol indicates the possibility of death or serious injury.

    CAUTION

    This symbol indicates the possibility of injury or damage to properties only.

    ■ The meanings of the symbols used in this manual are as shown below.

    Be sure not to do.
    Be sure to follow the instruction.

    WARNING
    ■ Installation
    Do not use damaged power
    cable.

    • There is risk of fire or electric
    shock.

    Install the panel and the
    cover of control box
    securely.
    • There is risk of fire or electric
    shock.

    Be cautious when
    unpacking and installing
    the product.
    • Sharp edges could cause injury.
    Be especially careful of the
    case edges and the fins on the
    condenser and evaporator.

    Be sure the installation area
    does not deteriorate with
    age.
    • If the base collapses, the air
    conditioner could fall with it, causing
    property damage, product failure,
    and personal injury.

    For electrical work, contact
    the dealer, seller, a qualified
    electrician, or an Authorized
    Service Center.
    • There is risk of fire or electric
    shock.

    Do not modify or extend the
    power cable.
    • There is risk of fire or electric
    shock.

    For installation, always
    contact the dealer or an
    Authorized Service Center.
    • There is risk of fire, electric
    shock, explosion, or injury.

    Always use the power plug
    and socket with the ground
    terminal.
    • There is risk of electric shock.

    Do not install, remove, or
    re-install the unit by
    yourself (customer).
    • There is risk of fire, electric
    shock, explosion, or injury.

    Do not install the product
    on a defective installation
    stand.
    • It may cause injury, accident, or
    damage to the product.

    Do not let the air conditioner
    run for a long time when the
    humidity is very high and a
    door or a window is left open.
    • Moisture may condense and
    wet or damage furnishings.

    Owner's Manual 3

    ENGLISH

    Safety Precautions



  • Page 4

    Safety Precautions

    ■ Operation
    Take care to ensure that
    power cable could not be
    pulled out or damaged
    during operation.

    Do not place anything on
    the power cable.

    Do not turn the breaker
    on/off or connect/disconnect
    the power supply cable
    during operation.

    • There is risk of fire or electrical
    shock.

    • There is risk of fire or electric
    shock.

    • There is risk of fire or electrical
    shock.

    Do not touch product with
    wet hands.

    Do not place a heater or
    other appliances near the
    power cable.

    Do not allow water to run
    into electric parts.

    • There is risk of fire or electrical
    shock.

    • There is risk of fire and electric
    shock.

    • It may cause There is risk of
    fire, failure of the product, or
    electric shock.

    Do not store or use
    flammable gas or
    combustibles near the air
    conditioner.

    Do not use the product in a
    tightly closed space for a
    long time.

    When flammable gas leaks,
    turn off the gas and open a
    window for ventilation
    before turn the product on.
    DO NOT use the telephone
    or turn switches on or off.

    • There is risk of fire or failure of
    product.

    • Oxygen deficiency could occur.

    • There is risk of explosion or fire.

    Unplug the unit if strange
    sounds, odors, or smoke
    comes from it.

    Stop operation and close
    the window in storm or
    hurricane. If possible,
    remove the air conditioner
    from the window before the
    hurricane arrives.

    Do not open the inlet grill of
    the product during
    operation. (Do not touch the
    electrostatic filter, if the unit
    is so equipped.)

    • There is risk of electrical shock
    or fire

    When the product is soaked
    (flooded or submerged),
    contact an Authorized
    Service Center.
    • There is risk of fire or eletric
    shock.

    4 Room Air Conditioner

    • There is risk of property
    damage, failure of product, or
    electric shock.

    Ventilate the product from
    time to time when operating
    it together with a stove, etc.
    • There is risk of fire or electrical
    shock.

    • There is risk of physical injury,
    electric shock, or product
    failure.

    Turn the main power off
    when cleaning the product.

    • There is risk of electrical shock.



  • Page 5

    Safety Precautions

    • There is risk of product damage
    or failure, or unintended
    operation.

    Take care to ensure that
    nobody could step on or fall
    onto the outdoor unit.

    ENGLISH

    When the product is not be
    used for a long time,
    disconnect the power supply
    cable or turn off the breaker.

    • This could result in personal
    injury and product damage.

    ■ Installation
    Always check for gas
    (refrigerant) leakage after
    installation or repair of
    product.
    • Low refrigerant levels may
    cause failure of product.

    Do not install the product
    where the noise or hot air
    from the outdoor unit could
    damage the neighborhoods.
    • It may cause a problem for your
    neighbors.

    Install the drain hose to
    ensure that water is drained
    away properly.
    • A bad connection may cause
    water leakage.

    Use two or more people to
    lift and transport the air
    conditioner.
    • Avoid personal injury.

    Keep level even when
    installing the product.

    • To avoid vibration or water
    leakage.

    Do not install the product
    where it will be exposed to
    sea wind (salt spray)
    directly.
    • It may cause corrosion on the
    product. Corrosion, particularly on
    the condenser and evaporator fins,
    could cause product malfunction
    or inefficient operation.

    ■ Operation
    Do not direct airflow at
    room occupants. (Don't sit
    in the draft.)

    Do not use the product for
    special purposes, such as
    preserving foods, works of
    art, etc. It is a consumer air
    conditioner, not a precision
    refrigeration system.

    • This could damage your health.

    • There is risk of damage or loss
    of property.

    Use a soft cloth to clean. Do
    not use harsh detergents,
    solvents, etc.

    Do not touch the metal
    parts of the product when
    removing the air filter. They
    are very sharp!

    • There is risk of fire, electric
    shock, or damage to the plastic
    parts of the product.

    • There is risk of personal injury.

    Do not block the inlet or
    outlet of air flow.

    • It may cause product failure.

    Do not step on or put
    anyting on the product.
    (outdoor units)
    • There is risk of personal injury
    and failure of product.

    Owner's Manual 5



  • Page 6

    Safety Precautions

    Always insert the filter
    securely. Clean the filter
    every two weeks or more
    often if necessary.
    • A dirty filter reduces the
    efficiency of the air conditioner
    and could cause product
    malfunction or damage.

    Do not insert hands or other
    objects through the air inlet
    or outlet while the air
    conditioner is plugged in.
    • There are sharp and moving
    parts that could cause personal
    injury.

    Use a firm stool or ladder when cleaning or
    maintaining the air conditioner.

    • Be careful and avoid personal injury.

    Do not drink the water
    drained from the unit.

    • It is not sanitary and could
    cause serious health issues.

    Replace the all batteries in the remote
    control with new ones of the same type. Do
    not mix old and new batteries or different
    types of batteries.
    • There is risk of fire or explosion

    ■ Disuse
    Do not recharge or disassemble the
    batteries. Do not dispose of batteries in a
    fire.
    • They may burn or explode.

    6 Room Air Conditioner

    If the liquid from the batteries gets onto
    your skin or clothes, wash it well with clean
    water. Do not use the remote if the batteries
    have leaked.
    • The chemicals in batteries could cause burns or
    other health hazards.



  • Page 7

    Prior to Operation
    ENGLISH

    Prior to Operation
    Preparing for Operation
    1. Contact an installation specialist for installation.
    2. Plug in the power plug properly.
    3. Use a dedicated circuit.
    4. Do not use an extension cord.
    5. Do not start/stop operation by plugging/unplugging the power cord.
    6. If the cord/plug is damaged, replace it with only an authorized replacement part.

    Usage
    1. Being exposed to direct airflow for a long time may be hazardous to your health. Do not expose
    occupants, pets, or plants to direct airflow for a long time.
    2. Due to the possibility of oxygen deficiency, ventilate the room when using the appliance together with
    stoves or other heating devices.
    3. Do not use this air conditioner for non-specified special purpose (e.g. preserving precision devices,
    food, pets, plants, or art objects). Such use may damage your properties.

    Cleaning and Maintenance
    1. Do not touch the metal parts of the unit when removing the filter. Injury can occur.
    2. Do not use water to clean inside the air conditioner. Exposure to water can destroy the insulation,
    leading to electric shock.
    3. When cleaning the unit, first make sure that the power and breaker are turned off. The fan rotates at a
    very high speed during operation. There is a possibility of injury if the unitʼs power is triggered while
    cleaning inner parts of the unit.

    Service
    For repair and maintenance, contact your authorized service dealer.

    Owner's Manual 7



  • Page 8

    Introduction

    Introduction
    Symbols used in this Manual
    This symbol alerts you to the risk of electric shock.
    This symbol alerts you to hazards that may cause harm to the
    air conditioner.

    NOTICE

    This symbol indicates special notes.

    Features
    This appliance should be installed in accordance with national wiring regulations. This guide acts as a
    guide to help to explain product features.

    Indoor

    Air inlet
    Grille tab
    Plasma filter (Optional)
    Front grille
    ON/OFF button

    Air filter

    Air outlet

    Louvers�
    (Vertical blades)

    Signal�
    receiver

    Flap�
    (Horizontal blade)

    Outdoor
    Air Intake
    (side, rear)

    Air Intake Vents

    Control cover
    Connecting wire
    Connection pipe
    Drain hose

    Air Outlet Vents

    Control cover
    Connecting wire
    Connection pipe
    Drain hose

    Base Plate
    Air Outlet

    8 Room Air Conditioner

    Base Plate



  • Page 9

    Electrical Safety
    ENGLISH

    Electrical Safety
    • This appliance must be properly grounded.
    To minimize the risk of electric shock, you must alway plug into a grounded oulet.
    • Do not cut or remove the grounding prong from the power plug.
    • Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the appliance
    unless the cover screw is metal and not insulated, and the wall receptacle is grounded through the
    house wiring.
    • If you have any doubt whether the air conditioner is properly grounded, have the wall receptacle and
    circuit checked by a qualified electrician.

    • The Power cord connected to the unit should be selected according to the following specifications .

    Temporary Use of an Adapter
    We strongly discourage the use of an adapter due to potential safety hazards. For temporary connections,
    use only a UL-listed adapter, available from most local hardware stores. Ensure that the large slot in the
    adapter is aligned with the large slot in the receptacle for a proper polarity connection.
    To disconnect the power cord from the adapter, use one hand on each to avoid damaging the ground
    terminal. Avoid frequently unplugging the power cord as this can lead to eventual ground terminal damage.

    • Never use the appliance with a broken adapter.

    Temporary Use of an Extension Cord
    We strongly discourage the use of an extension cord due to potential safety hazards. For temporary
    situations, use only CSA certified and UL listed 3-wire grounded extension cords, rated 15 A, 125 V.

    Owner's Manual 9



  • Page 10

    Operating Instructions

    Operating Instructions
    How to insert the Batteries
    1. Remove the battery cover by pulling it according to the arrow
    direction.
    2. Insert new batteries making sure that the (+) and (-) of battery are
    installed correctly.
    3. Reattach the cover by sliding it back into position.

    NOTICE
    Use 2 AAA(1.5volt) batteries.
    Do not use rechargeable batteries.

    Storage and Tips for using the Remote Controller
    • The remote controller may be stored by mounting
    it on a wall.

    • To operate the room air conditioner, aim the
    remote controller at the signal receptor.

    Signal Receptor
    Receives the signals from the remote control.(Signal receiving sound: two short beeps or one long beep.)

    Operation Indication Lamps

    OUT
    DOOR

    On/Off

    : Lights up during the system operation.

    Sleep Mode

    : Lights up during Sleep Mode Auto operation.

    Timer

    : Lights up during Timer operation.

    Defrost Mode

    : Lights up during Defrost Mode or Hot
    Start operation (Heat pump model only)

    OUTDOOR UNIT : Lights up during outdoor unit operation.
    OPERATION
    (Cooling model only)

    Operation indicating
    lamps

    Energy-Saving : Light up during Energy-Saving cooling mode operation. (optional)
    Plasma

    : The function illustrates its dynamic mode by using a multiple lighting system.

    10 Room Air Conditioner



  • Page 11

    Operating Instructions
    ENGLISH

    Remote Control Operation
    The Remote Controller transmits the signals to the system.

    1

    START/STOP BUTTON
    Operation starts when this button is pressed and
    stops when the button is pressed again.

    2

    OPERATION MODE SELECTION BUTTON
    Used to select the operation mode.

    3

    ROOM TEMPERATURE
    SETTING BUTTONS
    Used to select the room temperature.

    4

    INDOOR FAN SPEED SELECTOR
    Used to select fan speed in four steps
    low, medium, high and CHAOS.

    5

    JET COOL
    Used to start or stop the speed cooling/heating.
    (Speed cooling/heating operates super high fan
    speed.)

    6

    CHAOS SWING BUTTON
    Used to stop or start louver movement and set
    the desired up/down airflow direction.

    7

    ON/OFF TIMER BUTTONS
    Used to set the time of starting and stopping operation.

    8

    TIME SETTING BUTTONS
    Used to adjust the time.

    9

    TIMER SET/CANCEL BUTTON
    Used to set the timer when the desired time is obtained and
    to cancel the Timer operation.

    10

    SLEEP MODE AUTO BUTTON
    Used to set Sleep Mode Auto operation.

    11

    AIR CIRCULATION BUTTON
    Used to circulate the room air without cooling or heating.

    12

    ROOM TEMPERATURE CHECKING BUTTON
    Used to check the room temperature.

    Cooling Operation

    13

    NEO PLASMA(OPTIONAL)
    Used to start or stop the plasma-purification function.

    Auto Operation

    14

    RESET BUTTON
    Initialize remote controller.

    Healthy Dehumidification Operation

    15

    2nd F Button
    Used prior to using modes printed in blue at the bottom of
    buttons.

    16

    AUTO CLEAN
    Used to set Auto Clean mode.

    17

    HORIZONTAL AIRFLOW DIRECTION CONTROL
    BUTTON
    Used to set the desired horizontal airflow direction.

    Signal transmitter

    5
    6

    1
    3

    4
    2
    7
    11
    8
    13

    10
    CANCEL
    ON

    OFF

    9
    16

    SET
    AUTO CLEAN

    12
    17
    15

    14

    Flip-up door�
    (opened)

    Operation Mode

    Heating Operation

    • Cooling Model(� ), Heat Pump Model(� )

    (Heat Pump)

    (Cooling Only)

    Owner's Manual 11



  • Page 12

    Operating Instructions

    Cooling Operation

    1

    Press the Start/Stop button.
    The unit will respond with beep sound.

    2

    Open the door on the Remote Controller. To select Cooling
    Operation, press the Operation Mode Selection button.
    Each time the button is pressed, the operation mode is shifted
    in the direction of the arrow.

    Cooling

    Auto

    Healthy
    Dehumidification

    Heating
    (Heat pump model only)

    (Cooling Only (Heat Pump
    model)
    model)

    3
    ON

    Set the temperature lower than the room temperature.
    The temperature can be set within a range of 18°C~30°C in
    1°C.
    To raise the temperature

    To lower the temperature

    4

    You can select the fan speed in four stepslow, medium, high, or CHAOS. Each time the
    button is pressed, the fan speed mode is
    shifted.

    Natural wind by the CHAOS logic
    ❏ For more fresh feeling, press the Indoor Fan Speed Selector and set CHAOS mode. In this mode, the wind
    blows like natural breeze by automatically changing fan speed according to the CHAOS logic.

    12 Room Air Conditioner



  • Page 13

    Operating Instructions
    ENGLISH

    Auto Operation

    1

    Press the Start/Stop button.
    The unit will respond with beep
    sound.

    2

    Open the door on the Remote Controller. To select Auto
    Operation, press the Operation Mode Selection button.
    Each time the button is pressed, the operation mode is
    shifted in the direction of the arrow.

    Cooling

    Auto

    Healthy
    Dehumidification

    Heating
    (Heat pump model only)

    (Cooling Only (Heat Pump
    model)
    model)

    ON

    3

    The temperature and fan speed are automatically set by the
    electronic controls based on the actual room temperature. If
    you want to change the set temperature, press the Room
    Temperature Setting buttons. The set temperature will be
    changed considering room temperature.

    To raise the temperature

    To lower the temperature

    DURING AUTO OPERATION:
    ❏ You cannot switch the indoor fan speed. It has already been set by the Fuzzy rule.
    ❏ If the system is not operating as desired, manually switch to another mode. The system will not
    automatically switch from the cooling mode to the heating mode, or from heating to cooling, then you must
    set the mode and the desired temperature again.
    ❏ During Auto Operation, pressing the chaos swing button makes the horizontal louvers swing up and down
    automatically. If you want to stop auto-swing, press the chaos swing button again.

    Owner's Manual 13



  • Page 14

    Operating Instructions

    Healthy Dehumidification Operation

    1

    Press the Start/Stop button.
    The unit will respond with beep
    sound.

    2

    Open the door on the Remote Controller. To select Healthy
    Dehumidification Operation, press the Operation Mode
    Selection button.
    Each time the button is pressed, the operation mode is shifted
    in the direction of the arrow.

    Cooling

    (Cooling Only (Heat Pump
    model)
    model)

    3
    ON

    Auto

    Healthy
    Heating
    Dehumidification (Heat pump model only)

    Set the fan speed. You can select the fan
    speed in four steps - low, medium, high, or
    CHAOS. Each time the button is pressed,
    the fan speed mode is shifted.

    Natural wind by the CHAOS logic
    ❏ For more fresh feeling, press the Indoor Fan Speed Selector and set
    CHAOS mode. In this mode, the wind blows like natural breeze by
    automatically changing fan speed according to the CHAOS logic.

    DURING HEALTHY DEHUMIDIFICATION OPERATION:
    ❏ If you select the dehumidification mode on the operation selection button, the A/C starts to run the
    dehumidification function, automatically setting the room temp. and air volume to the best condition for
    dehumidification based on the sensed room temp.
    In this case, the setting temp. is not displayed on the Remote Controller and you are not able to
    control the room temp. either.
    ❏ During the healthy dehumidification function, the airflow volume is automatically set according to the
    optimization algorithm responding to the current room temp. So that room condition is kept healthy and
    comfortable even in the very humid season.

    14 Room Air Conditioner



  • Page 15

    Operating Instructions
    ENGLISH

    Heating Operation(Heat pump model only)

    1

    Press the Start/Stop button.
    The unit will respond with
    beep sound.

    2

    Open the door on the Remote Controller. To select Heating
    Operation, press the Operation Mode Selection button.
    Each time the button is pressed, the operation mode is
    shifted in the direction of the arrow.

    Cooling

    3
    ON

    Auto

    Healthy
    Dehumidification

    Heating
    (Heat pump model only)

    Set the temperature higher than the room temperature.
    The temperature can be set within a range of 16°C~30°C in
    1°C.
    To raise the temperature

    To lower the temperature

    4

    Set the fan speed again. You can
    select the fan speed in four steps–low,
    medium, high, or CHAOS. Each time
    the button is pressed, the fan speed
    mode is shifted.

    Natural wind by the CHAOS logic
    ❏ For more fresh feeling, press the Indoor Fan Speed Selector and set CHAOS mode. In this mode, the
    wind blows like natural breeze by automatically changing fan speed according to the CHAOS logic.

    Owner's Manual 15



  • Page 16

    Operating Instructions

    Jet Cool Operation

    1

    Press the Start/Stop button.
    The unit will respond with
    beep sound.

    2

    Press the Jet Cool button to operate the
    speed cooling mode and the unit will
    operate in super high fan speed on cooling
    mode for 30 minutes.

    3

    To cancel the Jet Cool mode, press the Jet Cool button or
    the fan button or the room temperature setting button again
    and the unit will operate in high fan speed in cooling mode

    or

    or

    NOTICE
    ❏ During the JET COOL function at any moment, the A/C starts to blow the cool air at
    extremely high speed for 30 minutes setting the room temp. automatically to 18°C. It is
    especially used to cool the room temperature quickly in a hot summer.
    ❏ In order to return to the normal cooling mode from the Jet Cool mode, you just press either
    the operation mode selection button, air volume selection or temp. setting button or the
    JET COOL button again.

    16 Room Air Conditioner



  • Page 17

    Operating Instructions

    1

    Press the Start/Stop button.
    The unit will respond with beep sound.

    2

    Open the door on the Remote
    Controller. Press the PLASMA air
    purifying operation ON/OFF button.
    Operation will start when the button
    is pressed and stop when the button
    is pressed again.

    3

    Set the fan speed. You can select the fan speed in
    four steps-low, medium, high or CHAOS.
    Each time the button is pressed, the fan speed
    mode is shifted.
    ❈ Air purifying operation (NEO PLASMA) can be
    with cooling, Heating or any other operations.

    NEO PLASMA Air Purifying Operation only
    If you press the only PLASMA button, only
    PLASMA purification function operates.
    Then, fan speed is low. You can select the fan
    speed in four steps-low, medium, high or CHAOS.
    Each time the button (
    ) is pressed, the fan
    speed mode is shifted.

    Owner's Manual 17

    ENGLISH

    NEO PLASMA Purification Operation(Optional)



  • Page 18

    Operating Instructions

    2nd F Operation

    1

    Press the Start/Stop button.
    The unit will respond with
    beep sound.

    2

    Open the door of the Remote Controller and press the 2nd F
    button to operate functions printed in blue at bottom of
    buttons.
    (Check the indication of 2nd function on Remote Controller
    display.)
    These buttons operate the timer setting as follows:
    CANCEL
    ON

    OFF

    SET
    AUTO CLEAN

    CANCEL
    ON

    OFF

    SET
    AUTO CLEAN

    3

    2nd function goes off in a short time automatically or when the
    button is pressed again.

    For more details, refer to functions next page.

    18 Room Air Conditioner



  • Page 19

    Operating Instructions
    ENGLISH

    Additional Features
    Sleep mode
    1. Press the Sleep Mode Auto button to set the time you want the unit to stop automatically.
    2. The Timer is programmed in one-hour increments by pressing the Sleep Mode Auto button 1 to 7 times. The
    sleep mode is available for 1 to 7 times. To alter the time period in steps of 1 hour, press the Sleep Mode
    Button while aiming at air conditioner.
    3. Make sure the Sleep Mode Auto LED lights up.
    To cancel the Sleep Mode, press the sleep Mode Auto button several times until the star
    (
    ) disappears from the operation display.
    NOTIC�
    E�The Sleep Mode will be operated at slow fan speed (cooling) or medium fan speed (heat pump
    only) for a comfortable sleep.
    In sleep mode: Chaos Swing function does not operate.
    In cooling mode or healthydehumidification mode:
    The temperature will automatically rise by 1°C over the next 30 minutes and by 2°C in 1 hour for a comfortable
    sleep.

    Setting the time
    1. Time can be set only when you press the Reset button. Having replacing the batteries,
    you should press the reset buttons to reset the time. Press the Start/Stop button.
    2. Press 2nd F button and check if 2nd F icon is on.
    3. Press the Time Setting buttons until the desired time is set.
    CANCEL�

    4. Press the Timer SET button.
    NOTIC�
    E� Check

    SET�

    the indicator for A.M. and P.M.

    Delay start/Pre-set stop
    1. Make sure the time is set correctly on the display of the remote controller.
    2. Press 2nd F button.
    3. Press the ON/OFF Timer buttons to turn Timer on or off.

    ON�

    OFF�

    4. Press the Time Setting buttons until the desired time is set.
    5. To set the selected time, press the Timer setting button aiming the remote controller at the
    signal receptor.

    CANCEL�
    SET�

    To cancel the timer setting
    CANCEL�
    Check if 2nd F icon is off.
    Press the Timer Cancel button aiming the remote controller at the signal receptor.
    SET�
    (The timer lamp on the air conditioner and the display will go out.)

    NOTIC�
    E�Select

    one of the following four types of operation.

    Del�
    ay�OFF T
    �imer�

    Del�
    ay�ON T
    �imer�

    with the unit running�

    Del�
    ay�OFF and ON T
    �imer� Del�
    ay�ON and OFF T
    �imer�

    Owner's Manual 19



  • Page 20

    Operating Instructions

    Vertical Airflow Direction Control
    The up/down airflow (Vertical Airflow) can be adjusted
    by using the remote control.

    1. Press the Start/Stop button to start the unit.
    2. Press Chaos Swing button and the louvers will
    swing up and down.
    Press the Chaos Swing button
    again to set the vertical louver
    at the desired airflow direction.

    NOTICE
    ❏ If you press the CHAOS swing button, the horizontal airflow
    direction is changed automatically based on the CHAOS
    algorithm to distribute the air in the room evenly and at the
    same time to make the human body feel most comfortable,
    as if enjoying a natural breeze.
    ❏ Always use the remote control to adjust the up/down
    airflow direction. Manually moving the vertical airflow
    direction louver by hand, could damage the air
    conditioner.
    ❏ When the unit is shut off, the up/down airflow direction
    louver will close the air outlet vent of the system.

    Horizontal Airflow Direction Control (Optional)
    The left/right(Horizontal Airflow) can be adjusted by using the remote control.
    Press the Start/Stop button to start the unit.
    Open the door on the remote control. Press the Airflow Direction Start/Stop button and the
    louvers will swing left and right. Press the Horizontal Airflow Direction Control Button again to
    set the horizontal louver at the desired airflow direction.

    Energy-Saving Cooling Mode (Optional)
    Energy-Saving Cooling Mode Can save energy in Cooling and Healthy Dehumidification Operation, because it can
    operate efficiently by setting body-adaptation time according to the change of time and temperature and adjusting
    automatically desired temperature.
    1. Press the Start/Stop button to start the unit.
    2. Open the door on the remote control.
    Select Cooling Operation or Healthy Dehumidification Operation.
    3. Press the Energy-Saving Cooling Mode button.
    4. To cancel the Energy-Saving Cooling Mode, press the Energy-Saving Cooling Model
    button and unit will operate in previous Mode(Cooling or Healty Dehumidification
    Mode).

    Heater Operation(Optional)
    1. Pressing the Heater button during Heating Operation enables the built-in heater
    to operate a strong heating function.
    2. If Heater Operation is on, Ho (Heater On) is shown at the Operation indication
    lamps and there is no change at the remote controller.
    NOTICE ❏ The heater consumes much electricity, so Heater Operation may cost more.
    ❏ If the Start/Stop button is pressed during Heater Operation, the indoor fan is
    operated to cool the heater for about 15 seconds and the unit stops
    operating.

    20 Room Air Conditioner



  • Page 21

    Operating Instructions
    ENGLISH

    Auto clean (Optional)
    1. Whenever you press the AUTO CLEAN button, Auto Clean Function will be
    reserved and cancelled.
    2. Auto Clean function works before and after cooling or dehumidification mode.
    For details, refer to the below points.
    3. When the unit is started after the reservation of Auto Clean ,the Cool Start
    function operates and indoor Fan is started after 20 seconds.
    4. When you press Start/Stop button to turn off the unit after the you have reserved
    Auto Clean function, the air-conditioner circulates the indoor air in the Auto
    Clean mode with no more Cooling or Dehumidification operation. For Cooling
    only model, it lasts for 30 minutes for Heat pump model, for 16 minutes.
    5. If you press the AUTO CLEAN button again during the product operation , Auto
    Clean function will be cancelled.

    AUTO CLEAN

    NOTICE
    ❏ During Auto Clean function, moistures left in indoor units after Cooling Operation or Healthy
    Dehumidification Operation can be removed.
    ❏ During Auto Clean function, only Start/Stop button, Plasma button and AUTO CLEAN button are
    available.

    Forced operation
    Operation procedures when the remote control can't be used.
    The operation will be started if the ON/OFF button is pressed.
    If you want to stop operation, re-press the button.

    ON/OFF�
    button

    Cooling Model
    Operating mode

    Cooling

    Room Temp. ≥ 24°C
    Cooling

    Indoor FAN Speed
    Setting Temperature

    High
    22°C

    High
    22°C

    Heat pump Model
    21°C ≤ Room Temp. < 24°C
    Healthy Dehumidification

    Room Temp. < 21°C
    Heating

    High
    23°C

    High
    24°C

    Test operation
    During the TEST OPERATION, the unit operates in cooling mode at high speed fan, regardless of room
    temperature and resets in 18 minutes.
    During test operation, if remote controller signal is received, the unit operates as remote controller sets.
    If you want to use this operation, Press and hold the ON/OFF button for 3~5 seconds, then the buzzer sound
    1 "beep".
    If you want to stop the operation, re-press the button.

    Owner's Manual 21



  • Page 22

    Operating Instructions

    Auto restart
    In case the power comes on again after a power failure, Auto Restarting Operation is the function to operate
    procedures automatically to the previous operating conditions.
    So there is no need of activating this function by pressing any key or button.
    In the initial mode, the fan operates at a low speed and the compressor starts 2.5~3 minutes later.
    As the compressor starts, the fan speed also resumes its previous setting mode.

    Helpful information
    Fan speed and cooling capacity.
    The cooling capacity indicated in the specification is the value
    when the fan speed is set to high, and the capacity will be lower
    at low or medium fan speed.
    High fan speed is recommended when you wish to cool the room
    quickly.

    High
    Speed

    Air Circulation Mode
    Circulates the room air without cooling or heating.
    1. Press the Start/Stop button. The unit will respond with beep sound.
    2. Open the door on the Remote Controller. Press the Air Circulation button. Now each time that you
    press the Indoor Fan Speed Selector, the fan speed is shifted from low to CHAOS and back to low
    again.

    CHAOS Air

    Fan speed is on low.

    Fan speed is on medium.

    Fan speed is on high.

    NOTICE

    ❏ CHAOS Air economizes power consumption and prevents overcooling. The fan speed is automatically
    changed from high to low or vice versa, depending on the ambient temperature.

    22 Room Air Conditioner



  • Page 23

    Maintenance and Service
    ENGLISH

    Maintenance and Service
    Before performing any maintenance, turn off the main power to the system.

    Indoor Unit
    Grille, Case, and Remote Control
    Turn the system off before cleaning. To clean, wipe with a soft, dry
    cloth. Do not use bleach or abrasives.
    NOTICE
    Air inlet vent

    Supply power must be disconnected before cleaning the indoor unit.

    Air filters

    Air outlet vent

    Air filters�
    (behind front panel)
    Vertical louver Horizontal louver

    The air filters behind the front grille should be checked and
    cleaned once in every 2 weeks or more often if neccessary.
    1. Pull the both sides and remove front panel.
    2. Pull the filter tab slightly forward to remove the filter.
    3. Clean the filter with a vacuum cleaner or warm, soapy water.
    • If dirt is conspicuous, wash with a solution of
    detergent in lukewarm water.
    • If hot water (40°C or more) is used, it may be
    deformed.
    4. After washing with water, dry well in the shade.
    5. Re-install the air filter.

    NEO PLASMA filter (Optional)
    The NEO PLASMA filter behind the air filters should be
    checked and cleaned once in every 3 months or more often if
    necessary.
    1. After removing the air filters, pull slightly forward to remove
    the NEO PLASMA filter.
    2. Clean NEO PLASMA filter with the vacuum cleaner.
    If it is very dirty, wash it with water.
    3. Note the cuts of electric discharge lines.
    4. Re-install the NEO PLASMA filter to the original position.

    TRIPLE DEODORIZER filter (Optional)
    1. After removing the air filters, pull slightly forward to remove
    the TRIPLE DEODORIZER filter.
    2. Dry in the sunlight for two hours.
    3. Re-install the TRIPLE DEODORIZER filter to the original
    position.

    Don't touch this NEO PLASMA Filter within 10 seconds after opening he inlet grille,
    it may cause an electric shock.
    Never use any of the followings:
    • Water hotter than 40°C
    Could cause deformation and/or discoloration.
    • Volatile substances
    Could damage the surfaces of the air conditioner.

    Pow

    d er

    G a s o li n e

    Owner's Manual 23



  • Page 24

    Maintenance and Service

    Replacement of purifying filter (Optional)
    Recomended use period : About 2 years
    1. Remove front panel and air filters.
    2. Remove air purifying filters.
    3. Insert new air purifying filters.
    4. Reinsert air filters and close front panel.
    Type 1: Open the front panel as shown.
    Then pull the filter tab slightly forward to remove the air filter.
    After removing the air filter remove the plasma and deodorizer filter by slightly pulling forward.

    Deodorizer�
    filter
    Plasma filter

    Type 2: Pull the front panel from both sides as shown.
    Then pull the filter tab slightly forward to remove the filter. After removing the air filter remove
    the plasma and triple deodorizer filter by slightly pulling forward.

    Deodorizer�
    filter
    Plasma filter

    Outdoor Unit
    The heat exchanger coils and panel vents of the outdoor unit should be checked regularly.
    If clogged with dirt or soot, the heat exchanger
    (Rear)
    and panel vents may be professionally steam cleaned.
    NOTICE
    Dirty or clogged coils will reduce the
    operating efficiency of the system and
    cause higher operating costs.

    Air intake
    vents

    (Side)

    Piping
    Drain Hose

    Air outlet
    vents
    (Rear)

    Air intake
    vents

    (Side)

    Piping
    Drain Hose

    Air outlet
    vents

    24 Room Air Conditioner



  • Page 25

    Maintenance and Service
    ENGLISH

    Common Problems and Solutions
    Before calling for service
    If you have problems with your air conditioner, read the following information and try to solve
    the problem. If you cannot find a solution, turn off the air conditioner and contact your dealer.
    Air conditioner does not operate
    1. Ensure that the air conditioner is plugged into a proper outlet.
    2. Check the fuse or circuit breaker.
    3. Check whether the voltage is unusually high or low.
    Air does not feel cold enough on the cooling setting
    1. Ensure that the temperature settings are correct.
    2. Check to see if the air filter is clogged with dust. If so, replace the filter.
    3. Ensure that the air flow from the outside is not obstructed and that there is a clearance of
    over 20" between the back of the air conditioner and the wall or fence behind it.
    4. Close all doors and windows and check for any source of heat in the room.

    Before calling for service, please review the following list of common problems and
    solutions.
    The air conditioner is operating normally when:
    • You hear a pinging noise. This is caused by water being picked up by the fan on rainy days
    or in highly humid conditions. This feature is designed to help remove moisture in the air
    and improve cooling efficiency.
    • You see water dripping from the rear of the unit. Water may be collected in the base pan in
    highly humid conditions or on rainy days. This water overflows and drips from the rear of
    the unit.
    • You hear the fan running while the compressor is silent. This is a normal operational
    feature.

    Owner's Manual 25



  • Page 26

    Maintenance and Service

    Troubleshooting
    Check the following points before requesting repairs or service.... If the fault persists, please contact your dealer or service center.

    Case

    Explanation

    See page
    21

    The air conditioner does not
    operate.

    • Check room temperature setting?
    • Check if circuit breaker is on?

    The room has a peculiar
    odor.

    • Check that this is not a damp smell exuded by
    the walls, carpet, furniture, or cloth items in the
    room.

    -

    It seems that condensation
    is leaking from the air
    conditioner.

    • Check the drain hose is connected tight or if
    indoor unit is installed even.

    -

    Air conditioner does not
    operate for about 3 minutes
    after turning on.

    • This is the protector of the mechanism.
    • Wait about 3 minutes and operation will begin.
    • About 3 minutes delay is applied to protect
    compressor from frequenty on/off.

    Does not cool or heat
    effectively.

    • Is the air filter dirty? See air filter cleaning
    instructions.

    25, 26

    • Has the temperature been set correctly?

    14, 17

    -

    -

    • Are the indoor unit's air inlet or outlet vents
    obstructed?

    -

    • For a noise that sounds like water flowing.
    -This is the sound of refrigerant flowing inside
    the air conditioner unit.
    • For a noise that sounds like the compressed
    air releasing into atmosphere.
    -This is the sound of the dehumidifying water
    being processed inside the air conditioning
    unit.

    -

    Remote Controller display is
    faint, or no display at all.

    • Are the batteries depleted?
    • Are the batteries inserted in the opposite (+)
    and (-) directions?

    12

    Crack sound is heard.

    • This sound is generated by the
    expansion/constriction of the front panel, etc.
    due to changes of temperature.

    -

    The air conditioner
    operation is noisy.

    26 Room Air Conditioner



  • Page 27






Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für LG AMNH24GD5L0 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Holen Sie sich Ihr Benutzerhandbuch per E-Mail

Geben Sie Ihre E-Mail-Adresse ein, um das Handbuch zu erhalten von LG AMNH24GD5L0 in der Sprache / Sprachen: Englisch als Anhang in Ihrer E-Mail.

Das Handbuch ist 18,69 mb groß.

 

Sie erhalten das Handbuch in Ihrer E-Mail innerhalb von Minuten. Wenn Sie keine E-Mail erhalten haben, haben Sie wahrscheinlich die falsche E-Mail-Adresse eingegeben oder Ihre Mailbox ist zu voll. Darüber hinaus kann es sein, dass Ihr ISP eine maximale Größe für E-Mails empfangen kann.

Andere Handbücher von LG AMNH24GD5L0

LG AMNH24GD5L0 Bedienungsanleitung - Deutsch - 27 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info