Bedienungsanleitung LG OLED48C31 (Seite 13 von 13) (Englisch)

815569

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

The descriptions in this manual are based on the buttons on the remote

control. Please read this manual carefully and use the TV correctly.

(Some buttons and services may not be provided depending on models or

regions.)

How to register the Magic Remote

Control

To use the Magic Remote, first pair it with your TV.

1 Put batteries into the Magic Remote and turn the TV on.

2 Point the Magic Remote at your TV and press the Wheel (OK) on the

remote control.

* If the TV fails to register the Magic Remote, try again after turning the TV

off and back on.

How to deregister the Magic Remote

Control

Press the (Back) and (Home) buttons at the same time, for five

seconds, to unpair the Magic Remote with your TV.

* Press and hold the (Home) and (Q. Settings) buttons for more

than 5 seconds to disconnect and re-register the Magic Remote at the

same time.

•It is recommended that an Access Point (AP) be located more than

0.2m away from the TV. If the AP is installed closer than 0.2m, the

Magic remote control may not perform as expected due to frequency

interference.

Using Always Ready

(Depending upon model)

You can operate the TV and connect to Bluetooth with direct voice recognition

while the power is off.

* → [ ] → [General] → [Always Ready], setting [Enable the

function] to on.

* Pressing the button while watching TV switches the screen to [Always

Ready] that is turned on, and pressing the button once more turns the

screen to [Always Ready] that is turned off.

* Press the (Home) button or the (Back) button to watch TV when

the screen is in [Always Ready] that is turned on.

* Press the Wheel (OK) button to display the wallpaper when the

screen is in [Always Ready] that is turned off, and press the button to

watch TV.

Note

•Using Always Ready may increase energy consumption.

•For more information about the feature, refer to the → [ ] →

[Support] → [User Guide] → [Troubleshooting] → [Learn More About

Always Ready].

Connecting Smart Devices using NFC

Tagging

NFC is technology that uses Near Field Communication (13.56MHz), allowing

you to conveniently send and receive information without separate settings.

By bringing a smart device near the NFC-enabled remote control, you can

install the LG ThinQ app and connect the device to the TV.

1 Turn on NFC in the smart device’s settings. To use NFC with Android

devices, set the NFC option to enable ‘read/write tags’ in the smart

device's settings. The NFC settings may vary depending on the device.

2 Bring the smart device near the (NFC) on the remote control. The

required distance for NFC tagging is about 1cm.

3 Follow the instructions to install the LG ThinQ app on your smart device.

4 Retagging the smart device to the remote control allows you to

conveniently access various features on the connected TV through the LG

ThinQ app.

Note

•This feature is available for NFC-enabled smart devices only.

•This feature is only available if the remote control has an NFC logo.

Specifications

Specifications (MR23GN, MR23GA)

Frequency range Output Power (Max.)

Bluetooth 2,400 to 2,483.5MHz 8dBm

NFC*13.553 to 13.567MHz -11.22dBuA/m @ 10m

* Only MR23GN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

LG OLED48C31 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von LG OLED48C31

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info