Bedienungsanleitung LG PREMTBB10 (Seite 59 von 84) (Englisch)

688100

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

117

INSTALLATION

116

INSTALLATION

ENGLISH

• When you remove the remote controller from the installation plate, insert a small flat head

screwdriver into the bottom side separation hole and turn clockwise to separate the remote

controller.

- There are 2 separation holes at the bottom part. Slowly separate one by one.

- Be careful not to damage the internal parts during the removal.

• Use the connection cables to connect the indoor unit with the remote controller.

• For the following cases, separately purchase and use the cables suitable for the situation.

- Do not install the cable over 50 m. (It may cause communication issues.)

- If the distance between the wired remote controller and the indoor unit is 10 m or more : 10

m extension cable (model name: PZCWRC1)

- If you control several indoor unit products with one wired remote controller : Group control

cable (model name: PZCWRCG3)

Wall Side

Please check if connector is normally connected.

Connecting cable

Indoor

Unit side

DC 12 V Red

Signal Yellow

GND Black

NOTE

During the wired remote controller installation, do not bury it in the wall. (It may cause

temperature sensor failure.)

Do not install the cable over 50 m. (It may cause communication defect.)

When you install the extension cable, carefully check the direction of the connectors on the

remote controller side and the product side before the installation.

Specification of extension cable: AWG 24, 3 conductor or above.

Group control

• It connects and controls 2 or more air conditioner indoor units to one wired remote controller.

※Connect using the group control cable.

① Group control cable (PZCWRCG3): Connect to indoor unit’s wired remote controller connector

② Extension cable (PZCWRC1): Connect to No. ① cable and slave indoor unit’s wired remote

controller connector

While No. ① cable is connected, connect No. ② cable.

• After checking the existence of the event communication in the product manual, change

master/slave of the remote controller.

※For details, refer to ‘remote controller master/slave’ contents.

• Change master/slave of the indoor unit.

- For ceiling cassette and duct product group, change the setting with the indoor unit PCB

switch.

RED(12V)

YELLOW(SIG)

BLACK(GND)

YELLOW(SIG)

BLACK(GND)

YELLOW(SIG)

BLACK(GND)

Indoor unit Main PCB

Indoor unit 1

Indoor unit 2 Indoor unit 3

Master Slave Slave

NOTE

• Connect only GND and signal cable to the indoor unit set as slave. (If power cable is also

connected, it may cause loss of communication)

• Inquiries related to the purchase of the cable shall be directed to the specialized company

and the service center.

Master Slave Slave

GND

12V

Signal cable

Black

Red

No. 3 switch OFF: master (factory ship-out based)

No. 3 switch ON: slave

YellowYellow

Yellow

1,MFL69312302,영영 2018. 11. 19. 영영 11:19 Page 116

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

LG PREMTBB10 Seite 59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von LG PREMTBB10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info