Bedienungsanleitung Liebherr SBSef 7242 (Seite 3 von 6) (Englisch)

715384

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

When moving the appliances, always take hold of them at

the outer front corners. On no account should you push with

your knee against the side walls or door.

The combined appliance is easiest to shift diagonally by

moving the left and right corner alternately.

Once the combined appliance is exactly in front of the aper-

ture, push it straight in.

If the combined appliance

has to be pulled out of the

aperture again, take hold of

it in the lower third area and

pull it straight forwards.

NOTICE

Risk of damage when moving the combined SBS appliance!

The combined SBS appliance is heavy once assembled. The

appliance may be dented by improper movement.

Observe the information given on moving the appliance (see

above).

Remove all protective film from the outside of the housing.

On the front of the appliance:

Fig. 4

If necessary, completely retract the height-adjustable feet

Fig. 4 (A)

at the front of both appliances so that they are not

touching the floor.

Place the caps

Fig. 4 (1)

onto the four front height-adjust-

able feet.

Push both appliances together up to approx. 10 mm apart so

that they stand flush at the front.

Fig. 5

Unclip and remove the covers

Fig. 5 (2)

The joining plate automatically aligns the height of the appli-

ances. If one appliance is slightly higher than the other, start

with that appliance.

Put the joining plate

Fig. 5 (3)

in place and fix it loosely to

one appliance with two screws

Fig. 5 (4)

Move the joining plate sideways so that the centre bar of the

plate lies on the side wall of the appliance. Tighten the

screws.

Now screw the joining plate to the other appliance. As you

do this, shift the appliances together or apart slightly as

necessary.

Fig. 6

If the appliance is fitted with the pre-mounted screw

Fig. 6 (7)

: Undo the screw.

The joining plate automatically aligns the depth of the appli-

ances. If one appliance is further forward than the other, start

with that appliance. Otherwise start with the appliance on the

left.

Fix the joining plate

Fig. 6 (5)

loosely to one appliance with

two screws

Fig. 6 (6)

Move the joining plate sideways so that the centre bar of the

plate lies on the side wall of the appliance. Tighten the

screws.

Now screw the joining plate to the other appliance. As you

do this, shift the appliances together or apart slightly as

necessary.

On the rear of the appliance:

Fig. 7

Insert the joining clamp

Fig. 7 (8)

at the top of the centre

side walls.

Insert the joining angle

Fig. 7 (9)

into the recess at the

bottom.

If the joining angle is too loose, fix it with a screw

Fig. 7 (10)

Note

To avoid vibration noise, ensure neither the clamps nor the

screws are in contact with the tubes on the rear of the appli-

ance!

On the front of the appliance:

Fig. 8

Side-by-side assembly

* Depending on model and options 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr SBSef 7242 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr SBSef 7242

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info