Bedienungsanleitung Line 6 Firehawk FX (Seite 14 von 16) (Englisch)

693634

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

The following table describes how the dierent processing Blocks are

indicated on the device while in Live Edit Mode.

BLOCK TYPE ABBREVIATION

IN LCD SCREEN

FOOTSWITCH LED

COLOR

Drives & Dynamics

DRV

Yellow

Compressor

CMP

Filters, Synths & Pitch

SYN

Purple

Modulation

MOD

Blue

Delays

DLY

Green

Reverb

REV

Orange

FX Loop

FXL

Turquoise

Looper

LPR

White

Amp

AMP

Red

Speaker Cabinet

CAB

Preset EQ

PEQ

• Select a Block to Edit: Press the footswitch assigned to the Block

that you wish to edit. You'll see the LCD rst show the full name

of the selected Block's current model, and and then display the

current model's rst parameter - now you're ready for editing.

Digital Delay

DLY:Time 430ms

First the full model name is shown, then its rst editable parameter

• To Edit the Current Parameter: Move the device's Expression

Pedal or Master Volume Knob to adjust the editable value. Or,

press the Bank Up  or Bank Down  footswitches to adjust the

value in ne increments. You'll see the parameter's current value

indicated in the LCD and by the Master Volume knob's LED ring.

• To Edit a Dierent Parameter: Repeatedly press the same

footswitch to cycle through all editable parameters for the current

model.

• You can adjust the value for one parameter, then simply tap

the footswitch again to edit another. Your edited values are

all retained until you exit Live Edit Mode, at which point you

choose to Save or discard them.

• Note that Model Select option allows you to choose a dierent

model type, which then becomes assigned to the current

footswitch.

• To Edit a Dierent Block: Press any other FS1–FS5 or A–D

footswitch to access its assigned block. You'll then be able to edit

its current model, or load a dierent model, using the same steps

mentioned above.

• To Exit Live Edit Mode: Press both the Bank Up  and

Bank Down  footswitches simultaneously.

Be sure to Save to retain your edited settings. See the previous

6. Preset & Bank Select Footswitches section for details on Save

Mode.

NOTE: The device's Tone, Reverb & FX knobs and the Tap Tempo

footswitch all continue to function while in Live Edit Mode.

Factory Reset & Pedal Calibration

Performing a Factory Reset restores the Firehawk FX to the original

factory settings and Presets. Be sure to use the Firehawk Remote app

to back up your customized Presets before performing a Factory

Reset! After performing a Factory Reset, it is recommended that you

next perform the Pedal Calibration for proper Pedal operation.

• Factory Reset: Simultaneously press and hold the Master Volume

Knob and the TAP footswitch as you power on the unit.

• Pedal Calibration: Power O your Firehawk FX device, then press

and hold footswitch A while powering On the unit. Follow the steps

in the LCD screen to calibrate the on-board Expression Pedal.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Line 6 Firehawk FX Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Line 6 Firehawk FX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info