Bedienungsanleitung Linksys E2000 Advanced Wireless-N (Seite 4 von 59) (Englisch)

602223

Zoom out

Zoom in

Vorherige Seite

1/59

Nächste Seite

Linksys E2000 Chapter 1: Product Overview

Advanced Wireless-N Router

Chapter 1: Product Overview

Thank you for choosing the Linksys E2000 Advanced

Wireless-N Router. The Router lets you access the Internet

via a wireless connection or through one of its four

switched ports. You can also use the Router to share

resources, such as computers, printers and files. A variety

of security features help to protect your data and your

privacy while you are online. Security features include Wi-

Fi Protected Access 2 (WPA2) security, a Stateful Packet

Inspection (SPI) firewall and Network Address Translation

(NAT) technology.

Setup and use of the Router is easy using Cisco Connect,

the software that is installed when you run the included

CD. Advanced configuration of the Router is available

through the provided browser-based utility.

Top

1, 2, 3, 4 (Green/Blue) These numbered LEDs,

corresponding with the numbered ports on

the Router’s back panel, serve two purposes.

The LED is continuously lit when the Router

is connected to a device through that port. It

flashes to indicates network activity over that

port. Green indicates Gigabit speeds, and blue

indicates 10/100 speeds.

Wi-Fi Protected Setup Button If you have

client devices, such as wireless adapters,

that support Wi-Fi Protected Setup, then you

can use the Wi-Fi Protected Setup button to

automatically configure wireless security for

your wireless network(s).

To use Wi-Fi Protected Setup, refer to

Wi-Fi Protected Setup, page 23.

Wireless (Blue) The Wireless LED lights up

when the wireless feature is enabled. If the LED

is flashing, the Router is actively sending or

receiving data over the network.

Internet (Blue) The Internet LED lights up

when there is a connection made through the

Internet port. A flashing LED indicates network

activity over the Internet port.

Power (Blue) The Power LED lights up when

the Router is powered on. When the Router goes

through its self-diagnostic mode during every

boot-up, the LED flashes. When the diagnostic

is complete, the LED is continuously lit.

Back

Internet Ethernet4 3 2 1 Reset

Power

12VDC

Internet Using an Ethernet cable (also called

a network or Internet cable), this Gigabit

port connects the Router to your Internet

connection, which is typically a cable or Digital

Subscriber Line (DSL) modem.

4, 3, 2, 1 Using Ethernet cables, these Gigabit

Ethernet ports (4, 3, 2, 1) connect the Router to

computers and other Ethernet network devices

on your wired network.

Reset There are two ways to reset the Router

to its factory defaults. Either press and hold the

Reset button for approximately five seconds,

or restore the defaults from Administration >

Factory Defaults in the Router’s browser-based

utility.

Power The Power port connects to the

included power adapter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Linksys E2000 Advanced Wireless-N Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Linksys E2000 Advanced Wireless-N

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info