Bedienungsanleitung Livington Instant Heater M23725 (Seite 5 von 12) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

783945

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Indoors, the Livington Instant Heater only warms up yourself and objects

such as carpets and furniture. Since the air is not heated, no dryness occurs.

OUTDOORS

The ambient air outdoors is constantly moving. A circulation heater proves

to be impractical here, because the heated air is simply blown away - the

heating eﬀect, which is supposed to supply you with heat, does not work.

However, the Livington Instant Heater allows you to heat certain areas

outdoors and keep objects and people around the heater warm with

maximum heating eﬃciency.

WALL MOUNTING

CAUTION:

The device is ﬁtted with a tilt sensor that ensures that the Livington

Instant Heater will only work if it is correctly installed. If the correct

angle of inclination is not maintained, e.g. if the device hangs crookedly or

lies on the ﬂoor, this inclination sensor prevents it from being switched on,

and Error E2 or 23 is displayed. It is only possible to switch on or operate the

Livington Instant Heater after it has been installed at the correct angle.

• The Livington Instant Heater may only be attached horizontally to

the wall. If you are using a standard plug connection, the help of an

electrician is not required for installation. An electrician is only necessary

if the heater is to be hard-wired to the wall.

• DO NOT install the heater on ﬂammable surfaces.

• The underside of the heater must be at a minimum height of 1.8 m above

the ﬂoor so that the heater cannot be touched accidentally when it is in

operation.

• When installing the heater, it must not be installed at an angle that

exceeds 90° or falls below 45° (see installation sketch).

• NOTE: If this angle of inclination is exceeded, the heater switches oﬀ

automatically.

• Make sure that the alignment is correct. The end of the cable and the

display should be on the left side.

• Keep the power cable away from the heater, as the device heats up when

it is in operation.

• When installing the heater, make sure that the prescribed minimum

distance between the heat radiator and ﬂammable surfaces is observed.

• The heater should always be at least 0.3 m away from the ceiling or

adjacent walls.

• Before drilling any holes, make sure that there are no wires or water pipes

in the immediate vicinity of the hole in the wall or ceiling.

• The heater must be attached to the supplied brackets.

• Secure the heater brackets securely to the surface onto which they are

installed using screws and dowels.

• Then attach the heater ﬁrmly to the brackets using the screws and nuts

provided.

• The brackets can be used to adjust the heater orientation. Adjust the

angle of inclination of the device by loosening the two wall screws.

Min: 450

Min: 300mm

Min: 1800mm

Max: 900

BASE

WALL

CEILING

WALL

WALL MOUNTING:

1. Measure and fasten so that the wall brackets are attached at a distance of

530 mm (centre holes).

2. Install the opposite bracket, but refrain from tightening the nuts.

3. Lift the heater to the height of the brackets. Then attach using the M8 nuts

and M8 rail bolts.

4. Turn the heater until it has the desired angle of inclination. Then tighten

all nuts.

OPERATING THE HEATER

• To switch the heater on, press the on/oﬀ switch on the underside of the

device, so that the display shows „0“.

• Press the temperature control on the front, the highest heating level 4

starts immediately. Press the temperature button followed by the arrow

keys on the remote control to set the desired heating level.

• Press the timer button and then use the arrow buttons to set the time until

the automatic switch-oﬀ.

• To return to standby mode, press the Standby Mode button on the remote control.

• Press the Sensor button on the remote control to set the motion sensor

mode. When motion is detected, the heater turns on for 15 minutes. If

no further movement is detected during these 15 minutes, the heating

element switches oﬀ (during this mode the display shows A-). If no

movement is detected in this mode for an hour, the heater switches to

normal standby mode.

• To reactivate the motion sensor mode, press the motion sensor button on

the remote control again.

• Pressing on the LEVEL button takes you straight to the highest heating level.

• To switch oﬀ the heater, press the on/oﬀ button on the underside of the

device.

LED DISPLAY

ON/OFF BUTTON

TEMPERATURE

REGULATOR

BATTERY

COMPARTMENT

REMOTE CONTROL

ON/OFF BUTTON

LEVEL

BATTERY REPLACEMENT

• Press the battery compartment button and slide out the battery holder.

• Remove the old battery and insert the new one. Make sure that the

positive pole of the battery is facing upward. Use only CR2025 or CR2032

batteries with the remote control.

• Push the battery holder back into the remote control, until you hear it click

into place.

Note: Always take care to ensure that no water or other liquids ever enter

the remote control.

CLEANING AND MAINTENANCE

• Always disconnect the heater‘s power supply and allow the device to cool

down before performing any maintenance work.

• DO NOT operate the device if dust or dirt has accumulated in or around the

heater.

• The heater is maintenance-free and can only be cleaned externally.

• Use a damp cloth to clean the exterior surfaces. DO NOT use strong,

aggressive or soluble cleaning agents when cleaning the heater, as these

M23725_M23726_LivingtonInstantHeater_Manual_201900803_CP.indd 5M23725_M23726_LivingtonInstantHeater_Manual_201900803_CP.indd 5 03.08.20 10:1003.08.20 10:10

Livington Instant Heater M23725 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info