Bedienungsanleitung Lorus R2303HX-9 (Seite 2 von 2) (Englisch)

690285

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

■ HOW TO USE TIMER

■ ENGAGEMENT/DISENGAGEMENT OF

ALARM & CHIME

1. Press Button D two times to go to the ALARM

mode.

2. With each press of Button B, the alarm and

chime can be engaged or disengaged in the

following order. The ALARM singal and/or

CHIME signal appear on the display

accordingly.

Both alarm and chime

are engaged.

Only alarm

is engaged.

Only chime

is engaged.

Neither alarm nor

chime is engaged.

Press Button D three times to go to the TIMER

mode. The TIMER mode indicator appears on the

display.

1. Press Button C to change the display to the

TIMER SETTING mode. The hour digits start

flashing.

2. Press Button B to set the hour digits. One digit

(flashing) is increased with each press of

Button B. The digits are increased quickly by

keeping Button B pressed.

3. Press Button D to confirm the hour setting and

move on to the minute setting. The minute

digits start flashing.

4. Press Button B to set the minute digits. One

digit (flashing) is increased with each press

of Button B. The digits are increased quickly

by keeping Button B pressed.

5. Press Button D to confirm the minute setting

and move on to the second setting. The

second digits start flashing.

6. Press Button B to set the second digits in the

same manner as the hour and minute setting.

7. Press Button C to complete the timer setting.

3. Press Button D to return to the TIME/

CALENDAR mode.

Note: The alarm can be set only in one time

zone.

How to stop the alarm while sounding

The alarm sounds for 10 seconds at the

designated time. To stop it manually while

sounding, press any Button.

TIMER OPERATION

1. Press Button B in the TIMER mode to start the

countdown timer.

2. Press Button B to stop the countdown timer.

3. To reset the timer, press Button C.

Press Button D to return to the TIME/CALENDAR

mode.

Start

Stop

Reset

Press Button D to return to the TIME/CALENDAR

mode.

The miniature battery SEIKO CR2016, Maxell

CR2016 or SONY CR2016 which powers your

watch should last approximately 2 years.

However, because it is inserted at the factory,

the actual life of the battery once in your

possession may be less than 2 years.

Be sure to replace the battery to prevent any

possible malfunction as soon as it runs down. To

replace the battery we recommend taking the

watch to a local watch repair shop.

Note: If the alarm is used for more than 20

seconds a day and/or the illuminating

light for more than 8 seconds a day, the

battery life may be less than the specified

period.

■ BATTERY CHANGE

■ HOW TO SET SECOND TIME ZONE

Press Button D four times to go to the SECOND

TIME ZONE. The SECOND TIME ZONE indicator

appears on the display.

1. Press Button C to change the display to the

TIME ZONE SETTING mode. The hour digits start

flashing.

2. Press Button B to set the hour digits. One digit

(flashing) is increased with each press of

Button B. The digits are increased quickly by

keeping Button B pressed.

3. Press Button D to confirm the hour setting and

move on to the minute setting. The minute

digits start flashing.

4. Press Button B to set the minute digits. The

minute digits are increased in 30-minute

increments.

5. Press Button C to complete the second time

zone setting.

■ HOW TO USE EL BACKLIGHT

In any mode press Button A to illuminate the

display for about 3 seconds.

Note:

1. The backlight of the watch employs an electro-

luminescent (EL) light, which tends to lose

illuminating power after very long use.

2. The illumination provided by backlight may be

hard to see when viewed under direct sunlight.

SECOND TIME ZONE

indicator

■ CARE OF YOUR LORUS WATCH

• BATTERY

CAUTION

Do not expose the old battery to fire

or recharge it. Keep it at a place

beyond the reach of children. If a

child swallows it, consult a doctor

immediately.

• WATER RESISTANT

Condition

of use

Accidental

contact

with water,

such as

splashes

and rain

Swimming

and taking

a shower

Skin

diving

Scuba

diving

Indication

on the dial/

case back

Indication

* If your watch is 200 M/20 BAR, 100 M/10 BAR

or 50 M/5 BAR water resistant, it is so

indicated on the dial/case back.

• Do not operate the buttons when the watch is wet.

• If the watch is exposed to salt water, rinse it in

fresh water and then wipe it thoroughly dry.

NO NO NO

YES

YES NO NO

YES YES NO

YES

WATER

RESISTANT

WATER

RESISTANT

(50M/5 BAR

)

WATER

RESISTANT

100M/10 BAR

or above

(

Caution:

Leather straps are not water resistant except so

indicated, even if the watch head is water resistant.

• ALLERGIC REACTION

Because the case and band touch the skin directly,

it is important to clean them regularly. If not, shirt

sleeves may be stained and those with delicate skin

may develop a rash. Please wear the watch with

some play to avoid any possible allergic reaction. If

you develop a rash on your wrist, stop wearing and

consult a physician.

• MAGNETISM

Your watch will not be affected by magnetism

generated by household electric appliances.

• SHOCKS AND VIBRATIONS

Your watch may be worn for normal sports

activities, but be careful not to drop it or hit it on

hard surfaces.

• TEMPERATURE

Your watch is preadjusted so that constant accuracy

may be insured at normal temperature.

■ SERVICE

When your LORUS watch requires repair or

sevicing, please see the enclosed WARRANTY/

GUARANTEE.

Printed in China

MINUTE SETTING(+30)

HOUR SETTING(+1)

TIMER mode indicator

MINUTE SETTING

HOUR SETTING

SECOND SETTING

ALARM mode indicator

TIME ZONE SETTING

MINUTE SETTING

HOUR SETTING

Z009_BLUE 06.5.26, 9:33 AM2

Lorus R2303HX-9 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Lorus R2303HX-9

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info