Bedienungsanleitung Lorus W150 (Seite 2 von 4) (Englisch)

593855

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

• To erase the data block by block:

In the block selection display, press button

“C” to select the block of data to be erased,

and then press and hold button “B” until

“DEL” appears. The data only in the selected

block is erased from memory.

How to clear the stored data

Notes:

1. When a block of data is erased, the block

number is reassigned accordingly.

2. When the stored data in all the blocks is

erased, the mode is automatically changed

to the STOPWATCH.

3. The stored data cannot be erased one by

one.

• To erase the data in all the blocks at a

stretch:

In the block selection display with any block

number shown, press and hold button “B”

until “FREE” appears. The data in all the

blocks is erased from memory.

■

TIMER MODE

• Up to 23 hours, 59 minutes and 59 seconds

can be set in second increments.

• After the set time is up, the timer counts

up the time up to 23 hours, 59 minutes and

59 seconds as many times as necessary

unless stopped and reset.

• The set time can be used repeatedly unless

canceled.

3. Press button “D” to set the flashing digits.

One digit is advanced with each press of

the button. Digits move quickly by keeping

button “D” pressed.

After all the adjustments are completed, press

button “B” to return to the TIMER mode

* If the watch is left untouched in the timer

setting display with the digits flashing,

it will automatically return to the TIMER

mode in 1 to 2 minutes.

Press button “A” to show the TIMER mode.

“TIMER” is displayed first, and then the TIMER

mode appears.

Timer setting

1. Press button “B” for 2 to 3 seconds to

show the timer setting display. The second

digits start flashing.

2. Press button “C” to select the digits to be

adjusted (flashing).

Minutes

HourSeconds

Current

time

Set time

Start

Stop

Restart

Time-up

* Warning

sound

beeps.

Stop

**Restart and stop of the timer

can be repeated by pressing button

“D”.

* When the set time is up, a warning

sound beeps for 10 seconds. To

stop it manually, press any of

the buttons.

Reset

Notes:

1. After the set time is up, the

timer counts up the time up to

23 hours, 59 minutes and 59

seconds as many times as necessary

unless it is stopped and reset.

2. Once the timer is set, the set

time is retained and can be used

repeatedly unless it is readjusted.

Timer operation

Press the buttons in the following order.

* With each press of the button, the stored

data is recalled successively from the

oldest to the newest.

Lap/

split 1

Lap/

split 2

Start

• A “Start-Finish-End” stopwatch operation

system is used. The data obtained from

the start till finish of a race is recorded as

a block and stored in memory.

Split time

Lap time

Finish

(Final lap/split)

EndReset

Number of

storable

data

1. Press button “C” to show the block selection

display. “RUN” and the block number are

displayed.

2. Press button “C” repeatedly to select the

desired block of data.

* With each press of the button, the block

number advances by one, starting from

Block 1.

3. Press button “D” to recall the stored data

in the block. The lap/split number is

displayed first, and then the lap time and

split time are displayed in the upper and

lower rows, respectively.

Memory recall operation

Press button “A” to show the MEMORY RECALL

mode. “RECAL” is displayed first, and then

the MEMORY RECALL mode appears.

Notes:

1. Up to 75 measurements can be stored in

memory. If more than 75 measurements

are made, the measurements over 75 will

not be stored in memory.

2. When the memory has become full and a

lap time/split time measurement is made,

“FULL” appears below the measured lap

time, indicating that the measurement data

is not stored in memory. To check the

memory capacity, change the mode to the

MEMORY RECALL mode, which displays

the number of storable data.

3. If the lap time measurement exceeds 60

minutes, any fraction less than a second

will be discarded when it is displayed.

The split time recalled in the MEMORY

RECALL mode, which is the accumulation

of the actual lap time measurements, therefore,

may not be exactly equal to the one displayed

when it was measured.

■

MEMORY RECALL MODE

• Up to 75 sets of lap times and split times

can be stored in memory.

• Measurement data obtained from the start

to finish of a race is recorded as a block, to

which a block number is assigned.

• Up to 38 blocks of data can be stored in

memory, and stored data can be recalled

block by block after the measurement.

* Lap time measured remains displayed for

5 seconds in the upper row. In the lower

row, the lap number is displayed, followed

by split time measured. Then, the measurement

in progress appears.

* The time elapsed from the finish of the

race until the end of the measurement will

not be included in the measurement.

** Lap time/split time can be measured repeatedly

by pressing button “C”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lorus W150 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Lorus W150

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info