Bedienungsanleitung M-System MSK951IX (Seite 3 von 20) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

680053

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

the charcoal filter inside the grease filter; fit the two filter retainers back on again to secure the charcoal filter.

OPERATION

Depending on the model, the unit is equipped with the following controls:

Controls shown in Fig. 12: Button A: light switch. Button B: first speed motor ON/OFF switch. Button C: second

speed switch. Button D: third speed switch. E: motor on light. THE MOTOR FUNCTION WARNING LIGHT (E) IS

NOT PRESENT IN SOME MODELS.

Controls shown in Fig. 13: Button A: Light switch; position 0: light off; position 1: light on. Button B: Motor

switch; position 0: motor off; position 1-2-3: motor on at speed I, II and III. C: Motor pilot lamp.

Controls shown in Fig. 14: Button A: turns the LIGHTS off. Button B: turns the LIGHTS on. Button C: decreases

speed down to minimum speed. If pressed for 2" the motor is turned off. Button D: activates the motor (calling

the last speed used) and increases the speed until reaching maximum. Button E: FILTER ALARM/TIMER RESET:

when pressing the key during display of the filter alarm (motor off) it resets the hour counter. When pressing the

key when the motor is running, the TIMER is activated and the hood will automatically be switched off after 5

minutes.

L1) The 4 green LEDs indicate the running speed.

L2) When the LED is red (motor off) it indicates the FILTER ALARM. When the LED is green (flashing) it indicates that

the TIMER has been activated with the key E.

FILTER ALARM: After 30h of operation, the LED L2 turns RED. It indicates that the grease filters need to be cleaned.

After 120h of operation, the LED L2 turns RED and flashes; It indicates that the grease filters need to be cleaned and

the charcoal filters replaced. After cleaning the grease filters (and/or replacing the charcoal filters), restart the hour counter

(RESET) by pressing the key E during display of the filter alarm.

Controls shown in Fig. 15: Button A: turns the lights off. Button B: turns the lights on.

Button C: decreases speed down to minimum speed. If pressed for 2" the motor is turned off.

If pressed for 2" when the Filter Alarm is active, the HOUR counter is reset.

Button D: starts the motor and increases the speed until reaching maximum

Button E: Activates/deactivates the sensor (AUTOMATIC or MANUAL mode). In automatic mode the sensor is active

and the LED L2 is on. The LEDs L1 indicate the running speed.

L1) The 4 GREEN LEDs signal the running speed.

L2) When the LED is GREEN it indicates AUTOMATIC mode. When it is off, it indicates MANUAL mode. When the LED

is RED, it indicates the Filter Alarm.

FILTER ALARM: Displayed for 30" when the motor is off:

After 30h of operation, the LED L2 turns RED. It indicates that the grease filters need to be cleaned.

After 120h of operation, the LED L2 turns RED and flashes; It indicates that the grease filters need to be cleaned and

the charcoal filters replaced.

After cleaning the grease filters (and/or replacing the charcoal filters), restart the hour counter (RESET) by pressing the

key C during display of the filter alarm.

GAS SENSOR SENSITIVITY: The sensitivity of the sensor can be modified to suit your requirements. To modify the

sensitivity, the appliance must be in manual mode (i.e. the LED L2 must be off); If not, press the key E.

Modify the sensitivity by simultaneously pressing the keys D and E. The set sensitivity is indicated by the 4 green LEDs.

By means of buttons C(-) and D(+) the desired sensitivity is set. Store the “new” sensitivity by pressing the key E.

ATTENTION: TO PREVENT DAMAGING THE SENSOR, DO NOT USE SILICONE PRODUCTS NEAR THE HOOD!

Controls shown in Fig. 16: Button A: turns the lights on/off; every 30 hours of operation the corresponding pilot

lamp (S) comes on to indicate that the grease filters must be cleaned; every 120 hours of operation the

corresponding pilot lamp (S) flashes to indicate that the grease filters must be cleaned and the charcoal filter

replaced. To restart the hour counter (RESET), hold the button A pressed down for about 2” (while the pilot lamp

S is on). Button B: drives the motor in first speed (the corresponding pilot lamp comes on); when holding it down

for about 1”, the motor cuts out; when pressing the button a second time (while the pilot lamp is on) , the TIMER

is activated and thus the motor stops after 5’ (the pilot lamp flashes). Button C: drives the motor in second speed

(the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp is on) ,

the TIMER is activated and thus the motor stops after 5’ (the pilot lamp flashes). Button D: drives the motor in

third speed (the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp

is on) , the TIMER is activated and thus the motor stops after 5’ (the pilot lamp flashes). Button E: drives the

motor in fourth speed (the corresponding pilot lamp comes on); when pressing the button a second time (while

the pilot lamp is on) , the TIMER is activated and thus the motor stops after 5’ (the pilot lamp flashes).

Pay special attention to the grease filters; to remove the filter: push inward on the clamp at the handle andpull the filter

downward. Wash out the filter using a neutral soap. If the model purchased has the controls shown in Figure 12/13: the

grease filter must be cleaned periodically: exactly how often depends on use (at leastonce every other month). If the

M-System MSK951IX Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info