Bedienungsanleitung M-System MST-90 (Seite 3 von 20) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

522905

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

C) Decreases speed down to minimum speed. If pressed for 2" the motor is turned off.

D) Activates the motor (calling the last speed used) and increases the speed until reaching maximum.

E) FILTER ALARM/TIMER RESET: when pressing the key during display of the filter alarm (motor off) it resets the hour

counter. When pressing the key when the motor is running, the TIMER is activated and the hood will automatically be switched

off after 5 minutes.

L1) The 4 green LEDs indicate the running speed.

L2) When the LED is red (motor off) it indicates the FILTER ALARM. When the LED is green (flashing) it indicates that

the TIMER has been activated with the key E.

FILTER ALARM:

After 30h of operation, the LED L2 turns RED. It indicates that the grease filters need to be cleaned.

After 120h of operation, the LED L2 turns RED and flashes; It indicates that the grease filters need to be cleaned and

the charcoal filters replaced.

After cleaning the grease filters (and/or replacing the charcoal filters), restart the hour counter (RESET) by pressing the

key E during display of the filter alarm.

CONTROLS shown in Fig. 19:

A) LIGHTS on/off switch.

1) Activates the motor at the first speed (the icon lights-up). By pressing on the icon for about 2 seconds the motor will stop.

2) Activates the motor at the second speed (the icon lights-up). All of the other icons relative to the speed remain switched off.

3) Activates the motor at the third speed (the icon lights-up). All of the other icons relative to the speed remain switched off.

4) Activates the motor at the fourth speed (the icon lights-up). All of the other icons relative to the speed remain switched off.

B) Activates the TIMER (the icon lights-up). By activating the Timer (5 minutes), the motor will stop automatically after 5 minutes.

C) FILTER ALARM. After 30 working hours, the icon lights up to indicate that the grease filter/s must be cleaned.

After 120 working hours, the icon flashes to indicate that the grease filter/s must be cleaned and the charcoal filters replaced.

To re-start the hour - counter, reset by pressing on the icon while it is lit (or while it flashes).

Grease filters: special attention must be given to the grease filters which must be periodically cleaned, whenever

the grease filter alarm trips. For instructions of the filter Alarm, refer to the Controls paragraph.

- Removing the grease filter (for models with metal panels): Remove the front panels by gripping them on the right (or

left) and pulling until the 2 internal pins are released. Operate in the same way on the opposite side of the panel;

slightly move the panel upwards until the 2 tabs slip out of the slots (Fig. 3). Remove the grease filters by pushing

the catch downwards and turning the filter outwards (Fig. 4).

- Removing the grease filter (for models with glass panels): Open the front panels gripping them at the bottom (Fig.5).

Remove the grease filters by pushing the catch downwards and turning the filter outwards (Fig. 4).

Charcoal filters: if the filtering version appliance is used, the charcoal filters will have to be periodically replaced

when the charcoal filter alarm trips. For instructions on the filter Alarm, refer to the Controls paragraph.

- Remove the charcoal filter (for models with metal panels): Remove the upper panel gripping it on the right (or left)

and pulling until the 2 internal pins are released. Operate in the same way on the opposite side of the panel; slightly

move the panel upwards until the 2 tabs slip out of the slots (Fig. 3). Remove the upper grease filter by pushing the

catch downwards and turning the filter outwards (Fig. 4). Remove the charcoal filters by turning them clockwise (Fig.

20).

- Removing the charcoal filter (for models with glass panels): Open the upper panel by gripping it at the bottom (Fig.5).

Remove the grease filter by pushing the catch downwards and turning the filter outwards (Fig. 4). Remove the

charcoal filters by turning them clockwise (Fig. 20).

Lighting (Fig.21): To replace the halogen lamps, open the cover by prising in the slots. Replace with lamps of the

same type. WARNING: Do not touch the new lamp with bare hands.

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative

consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling

of this product. The symbol on the product indicates that this product may not be treated as household waste. Instead

it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal

must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information

about treatment, recovery and recycling of this product, please contact your local city office, your household waste

disposal service or the shop where you purchased the product.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

M-System MST-90 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info